Power Supply Transformer 220V AC/DC 2A 5V

Addressable 5050 RGB LED bar (5mm x 5mm) with low current draw. LEDs can be joined by connecting the output of one module to the input of another.
Data line with a very specific protocol, requires a real-time microcontroller AVR, Arduino, PIC, mbed, etc. A minimum 8 MHz processor is required.

High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 2 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user.

Fan 12V 2x 3D Printer Cables features:
- Voltage: 12V
- Consumption: 65mA
- Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10%
- Screw diameter: 4.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 11cm
- Dimensions: 40mm x 40mm x 10mm

It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector.

The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features:
- Operating voltage: 3 to 5 VDC
- Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds
- Working current 2.5mA
- Iterfaz 1-wire
- Dimensions: 2.3 x1.2x 0.5cm
- Quantity: 1 unit

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

The zirconium ceramic tip of the CD-200/201 combines the wear resistance of a metal tip with the non-conductive and non-inductive properties of the plastic.
Ceramic alignment tool CD-20 features:
- Length: 11.5 cm,
- Screwdriver tip: flat,
- Tip length: 2mm.
- Suitable for: potentiometers, watchmaking, electronics components.

It consists of a 16-character, 2-row display.
The display is compatible with the HD44780 controller.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. 16x2 1602 LCD display HD44780 Backlit Blue background features:
- LCD screen , 16 characters and 2 lines
- 5V power supply
- HD44780 compatible controller
- Backlit blue background, white letters
- Include an adjustable contrast pin
- Dimensions (mm): 80 x 36 x 12