DC Buck Boost Converters

This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117.
The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features:
- Based on the regulator AMS1117-5V
- Input voltage: 4.5-12VDC
- Output voltage: 5VDC (+/- 0.05V)
- Max output current: 800mA
- Operating temperature: -40C to + 150C
- PCB size: 25x12 mm

This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A.
It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling.
Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features:
- Input voltage: DC 8V-40V
- Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output)
- Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally
- Output power: Max 150W
- Key components:
- Electrolytic capacitors 470µF - 50V

This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port.
The output voltage and voltage can be adjusted thanks to two potentiometers present in the module.
It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V
- Output voltage: 1.25-32 V continuously adjustable
- Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer,
- Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power)
- Operating temperature: -40 ° C - + 150 ° C

This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards.
Each channel has its switch for configure the output voltage to 3.3V or 5V.
Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering. Micro USB Interface Power Supply DC 7-12 VDC features:
- Operating voltage: DC 7-12 V
- Power display LED
- 1 Jack Female connector 2.1 mm to supply
- 1 AMS1117 3.3V regulator
- 1 AMS1117 5V regulator
- 4 3x2 connectors
- 1 5V micro USB female outlet
- Size: 5.5x3.5x1.5 cm

Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 5 VDC,
- Fixed output voltage: 5 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 12 VDC,
- Fixed output voltage: 12 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA.
Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off.
Works with frequency signals up to 1.5 MHz.
Characteristic:
- Input voltage range: 2.5 - 7 VDC,
- Fixed output voltage: 9 VDC,
- On / off mode pin EN: signal EN allowing this function to be performed,
- Output accuracy: ± 0.1 V,
- Output current: 150 - 400 mA,
- No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV,
- DC-DC conversion quality: 89%
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 19x15 mm.

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.

DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.
Use a multimeter to check the output voltage and adjust the potentiometer.

DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA.