Arduino sensors

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features:
- Adjustable High Sensitivity Acoustic Sensor
- LM393 comparator chip
- Integrated indicator LED
- AO analog output, output voltage signal in time real microphone
- DO digital output, sensitivity adjustable through potentiometer
- Frequency Range between 30 and 15000 Hz
- Power 4 ~ 6V
- Measurements 36x16x15mm

5.8GHz Doppler Radar Motion Sensor features:
- Microwave motion detector module
- The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications.
- High resistance to radio-frequency interference
- Frequency: 5.8GHz
- Operating Voltage: 3.3V - 20V TTL 3.3V
- Standby Current: 3mA
- Detection Range: 3-8 meters, 360 degrees
- Power of Output: 2mW
- Dimensions: 32x23 mm
- R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k
- R9 - for sensitivity adjustment

Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog
- Power: 5V
- Accuracy: 1.5%
- Measuring capacity: +/- 30A
- Dimensions: 31 x 13 mm

The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features:
- Operating voltage: 3 to 5 VDC
- Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds
- Working current 2.5mA
- Iterfaz 1-wire
- Dimensions: 2.3 x1.2x 0.5cm
- Quantity: 1 unit

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features:
- This sensor can be configured as auto Z axis level
- Sensor detection switch inductive proximity LJ12A3-4-Z / BY
- PNP DC6-36V
- Often used for 3D printer bed leveling
- Typical application: printer bed level sensor 3D
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- PNP NO (Normal Open)
- Detecting Distance 4mm - DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum
- Operating temperature -25 ° C at + 55 ° C (Non-freezing condition)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features:
- Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Concentration detection:
  200ppm - 5000ppm LPG, propane
  300ppm - 5000ppm butane
  5000ppm - 20000ppm methane
  300ppm - 5000ppm H2
  100ppm -2000ppm alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-4 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-4 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
200ppm- 10000ppm CH4, natural gas
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MG-5 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-5 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
- 200ppm - 10000ppm LPG, LNG, natural gas, propane,
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:
- Chip: MPU-6050
- Power supply: 3V-5V
- Operating current: 5mA
- Communication: I2C
- 16-bit analog-digital converter on all axes
- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)
- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)
- Dimensions: 14 x 21 x 1.3mm
- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin)

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

Easily convert water level to analog signal
The analog output signal can be read directly on the Arduino board
Characteristic:
- Operating voltage: 3.3V -5 V
- Consumption: less than 20 mA - Sensor type: Analog
- Operating temperature: 10º C -30º C
- Detection area: 40 mm x 16 mm
- Dimensions: 60 mm x 20 mm

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables

Microwave motion detector module.
The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications.
High resistance to radio frequency interference.
Characteristic:
- Frequency: 10.525GHz
- Frequency Accuracy: 3MHz
- Minimum Output: 13dBm EIRP
- Operating Voltage: 5V ± 0.25V
- Operating current (CW): 60mA maximum, 37mA typical
- Harmonic emissions: -10dBm
- Detection Range: Over 20 meters
- Power of Output: 5mW
The device is sensitive to electrostatic discharge and can be damaged during welding.
The IF output is particularly sensitive.

High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases.  The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it.
MQ-135 Air Quality Sensor features:
- Main chip: MQ-135 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
   10ppm - 300ppm NH3
   10ppm - 1000ppm Benzene
   10ppm - 300ppm Alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-9 Carbon Monoxide Sensor Module features:
- Main chip: MQ-9 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
   20ppm- 2000ppm carbon monoxide
   500ppm- 10000ppm methane CH4
   500ppm- 10000ppm LPG
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-8 Hydrogen Gas Sensor Module features:
- Main chip: MQ-8 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
  100ppm- 10000ppm hydrogen H2
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-6 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-6 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
- 200ppm- 10000ppm LPG, LNG
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

Sensor Module GUVA-S12SD UV features:
- The module based on the Schottky-type photodiode - applicable to the optical mode
- This is a " true "UV sensor instead of calibrated light sensor
- It has high sensitivity, high stability, good linearity
- Power supply: 2.5V - 5V
- Analog output
- Captured wavelength: 240-370nm
- Ultra low power consumption
- Meteorological applications, skin care, industrial UV level measurement
- PCB dimensions: 11x27mm

Capsule Electret Condenser Microphones 9.5 MIC features:
- Measures: 9.7 x 6.7mm
- Impedance: 1.5kΩ
- Working current: 0.5mA
- Working voltage: 4.5V (1.5-10V)
- Bandwidth: 50 ... 16000Hz
- Signal to noise ratio: ‰¥58dB
- Sensitivity: -42 ± 3dB
- Sensitivity tolerance: ± 3dB
- Distance between terminals: 2.54mm

Sound detection module for Arduino projects, smart cars.
Sound Detection Sensor Module features:
- Adjustable High Sensitivity Acoustic Sensor
- Chip LM393
- Red LED indicator integrated
- Frequency range between 30 and 15000 Hz
- Power 4 ~ 6V
- Measures 32x16x10mm

Arduino compatible IR motion detector with a detection range of 3 meters.
One sensor electric pyro, which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32.
Characteristic:
- Operating voltage: 4.5V- 20V
- Consumption in idle state: