Arduino sensors

Sensor Module FZ0888 IR Infrared Speed Meter features:
- The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position
- The module has a digital output (DO) which can be connected to your preferred microcontroller.
The operating mode:
- When the sensor is blocked, the DO output is high
- The AO signal is not enabled in this module
- Power supply: 3.3-5V
- Power consumption current 20 mA max
- PCB dimensions: 32 x 14 mm

Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features:
- Operating range: 0.2mm to 15mm
- Receiver: Phototransistor
- Emitter: Infrared Led
- Wavelength: 950 nm

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

Support for ultrasounds, HC-SR04 distance meter.
Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features:
- Material: Acrylic
- Color: transparent
- Includes screws

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.
Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features:
- Supply voltage: 5V (4.5V-6V)
- Consumption: typical 30 mA, (35 mA max)
- Interface: VCC, GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED measurement indicator in progress
- Frequency: 40 kHz for 200 μs
- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic
- Transparent color
- Includes screws

Descripción: Light sensor module to measure light intensity and obtain digital data from it.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features:
- Chip BH1750FVI
- Supply voltage 3V-5V
- Integrated 16bit AD converter
- Detection range: 0-65535 lx (with an accuracy of 1 lux)
- Interface: II2C
- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)
- Dimensions 18.4 x 14 mm

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Barometric Pressure, Temperature and Altitude Sensor BMP180 features:
- Module based on the atmospheric pressure sensor BMP180
- Supply voltage: 1.8 - 3.6 V
- Energy consumption: 0.5uA
- I2C interface
- Measuring range: 300 - 1100hPa
- Dimensions: 10 x 13 mm
- Includes soldering pins

Characteristic: - Supply voltage: 4.5V- 5.5V
- Consumption: 30 mA typical
- Analog output
- Range: 10cm to 80cm
- Dimensions: 29x12mm
- Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino

Sensor used to measure the current in the circuit to which it is connected.
It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features:
- Output: Analog
- Power: 5V
- Accuracy: 1.5%
- Measuring capacity: +/- 20A
- Dimensions: 31 x 13 mm

Ideal for projects with ARDUINO, Smart Car
Detects transparent and translucent obstacles
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:
- Current consumption: up to 100 mA
- Supply voltage 5V
- Current consumption <25mA
- Response time of 2 ms
- Measured distance: 3-80cm 15st angle
- Screw to adjust the sensitivity, the back
- Output status led indicator
- Operating temperature: -25°C - + 55°C
- Material: high-strength plastic
- Type of output: normally open, NPN
- Dimensions: 18 mm in diameter, Length 45 mm
- Cable length 55cm
- Departures:
      - Brown: +
      - Blue: -
      - Black: OUT

2x CNY70 Reflective Optical Sensor with Transistor Output features:
- Reflective optical sensor with transistor output
- Reflective optical coupler used to distinguish edge or line detection
- Dimensions of the housing are 7 x 7 x 6 mm
- Supply voltage: 5V
- Maximum diode current: 50 mA
- Maximum collector-emitter voltage: 32V
- Maximum collector current of 50 mA
- Quantity: 2 units

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

Level sensor for liquids with float.
The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low.
Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums.
Characteristic:
- Maximum Load: 50W
- Maximum Switching Voltage: 250V
- Maximum Switching Current: 0.5A
- Maximum charging current: 1A
- Operating temperature: -10ºC to + 60ºC
- Size: 58mm x 18mm

Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 ° C to 125 ° C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
             - Vcc red
             - Yellow digital output
- Inocidable steel
- Cable length: 3m

M18 Inductive Proximity Sensor features:
- Inductive proximity sensor detection switch LJ18A3-8-Z / BX
- NPN DC6-36V
- A Often used for 3D printer bed leveling
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open )
- Detecting distance 8mm
- DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition)
- Head diameter 18 mm
- Size 6.9 x 2cm
- Cable length 90cm

Ethanol alcohol sensor module.
MQ gas sensor uses a small indoor heater with an electrochemical sensor.
When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:
- Main chip: alcohol sensor MQ-3 and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Detection concentration:
- 0.05mg/L - 10mg/L
- Quick response features:
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features:
- Voltage Operating: 3 to 5.5 VDC
- Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds

Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:
- Device function: Temperature sensor
- Type of output: Digital
- Supply voltage: 3V to 5.5V
- Accuracy: ± 0.5ºC
- Temperature threshold: Programmable
- Operating temperature: -55ºC to + 125ºC
- Encapsulated: TO-92
- Supply current: 1.5mA

Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:
- Power supply from 5 to 30 Vdc
- Connection through analog input
- Temperature range from -40ºC to 100ºC
- Linearity +10 mV / ºK
- Accuracy of measurement: ± 2 ° C
- Manufacturer: Texas Instruments

Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 2m  

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features:
- Adjustable High Sensitivity Acoustic Sensor
- LM393 comparator chip
- Integrated indicator LED
- AO analog output, output voltage signal in time real microphone
- DO digital output, sensitivity adjustable through potentiometer
- Frequency Range between 30 and 15000 Hz
- Power 4 ~ 6V
- Measurements 36x16x15mm

5.8GHz Doppler Radar Motion Sensor features:
- Microwave motion detector module
- The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications.
- High resistance to radio-frequency interference
- Frequency: 5.8GHz
- Operating Voltage: 3.3V - 20V TTL 3.3V
- Standby Current: 3mA
- Detection Range: 3-8 meters, 360 degrees
- Power of Output: 2mW
- Dimensions: 32x23 mm
- R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k
- R9 - for sensitivity adjustment

Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog
- Power: 5V
- Accuracy: 1.5%
- Measuring capacity: +/- 30A
- Dimensions: 31 x 13 mm

The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features:
- Operating voltage: 3 to 5 VDC
- Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds
- Working current 2.5mA
- Iterfaz 1-wire
- Dimensions: 2.3 x1.2x 0.5cm
- Quantity: 1 unit

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features:
- This sensor can be configured as auto Z axis level
- Sensor detection switch inductive proximity LJ12A3-4-Z / BY
- PNP DC6-36V
- Often used for 3D printer bed leveling
- Typical application: printer bed level sensor 3D
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- PNP NO (Normal Open)
- Detecting Distance 4mm - DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum
- Operating temperature -25 ° C at + 55 ° C (Non-freezing condition)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features:
- Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Concentration detection:
  200ppm - 5000ppm LPG, propane
  300ppm - 5000ppm butane
  5000ppm - 20000ppm methane
  300ppm - 5000ppm H2
  100ppm -2000ppm alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-4 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-4 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
200ppm- 10000ppm CH4, natural gas
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MG-5 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-5 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
- 200ppm - 10000ppm LPG, LNG, natural gas, propane,
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:
- Chip: MPU-6050
- Power supply: 3V-5V
- Operating current: 5mA
- Communication: I2C
- 16-bit analog-digital converter on all axes
- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)
- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)
- Dimensions: 14 x 21 x 1.3mm
- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin)

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

Easily convert water level to analog signal
The analog output signal can be read directly on the Arduino board
Characteristic:
- Operating voltage: 3.3V -5 V
- Consumption: less than 20 mA - Sensor type: Analog
- Operating temperature: 10º C -30º C
- Detection area: 40 mm x 16 mm
- Dimensions: 60 mm x 20 mm

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables