ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €4.49
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €4.76 -€1.00 Price €3.76
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.90
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €21.99
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 ✗ Out-of-Stock Price €8.99
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €3.15