Power socket tester with RCD test function Uni-T UT07B-EU

Test pen for non-contact voltage detection with LED torch and buzzer. Allows to differentiate between different lines of alternating current. AC voltage detection range is 24-1000V

The device is designed to find and identify cables without disturbing the insulation. Finds broken wires, fault points and continuity test.

Test pen for non-contact voltage detection with buzzer. It can detect AC current up to 500V and DC current up to 60V. 

This detector complies with IEC61010 standards: pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation

Test pen for non-contact voltage detection. It can detect AC current up to 500V and DC current up to 60V. 

This detector complies with IEC61010 standards: pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.

Tester for RJ45 cables for Ethernet networks and coaxial cables.

- 8 LED status and configuration indicators.

- Supports UTP,FTP ,RG-58,59,etc... cable.

The tester is designed to test RJ45 network cabling: UTP, FTP, STP and telephone cables: RJ11 and RJ12. 8 LEDs for testing each individual conductor of an RJ twisted pair (cable is connected correctly when parallel LEDs 1-1 to 8-8 light up simultaneously).

8-channel oscilloscope for vehicle testing.
More than 80 kinds of automotive diagnostic functions (ignition detection / sensor / bus detection / performance / starting and charging circuits , etc.). The video help function provides the diagnostic video help that can be viewed online. The diagnostic result can be generated a diagnostic report, printed or taken a screenshot by pressing a key, many methods to save the data. Supported for recording waveform for a long time. You can simulate the camshaft and crankshaft signal. Transmit signals through the USB 2.0 plug and play interface, and requires no additional power supply; Key Hantek 1008C PC Oscilloscope USB 8 Channel Automotive Diagnostic DAQ features:

UT363S mini wind speed and temperature meters. UT363S measures wind speeds up to 30 m/s (108 km/h) with an accuracy of 0.01. The following units of measurement are available: m/s, km/h, ft/min, knots, mph.

The tester is designed to test RJ45 network cabling: UTP, FTP, STP and telephone cables: RJ11 and RJ12. 8 LEDs for testing each individual conductor of an RJ twisted pair (cable is connected correctly when parallel LEDs 1-1 to 8-8 light up simultaneously).

DDS UNI-T UTG932E 2-channel signal generator can generate sine wave, square wave, triangle wave, pulse wave and arbitrary wave, etc. The maximum output frequency of sine wave is 30MHz, sampling rate of 200 MSa/s.

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms

USB SALEAE is an 8-channel logic analyzer without memory, a maximum sampling speed of 24MHz (depends on the PC and the use of the USB bus).
It allows you to record and display digital data read on the computer.
Logic Analyzer 8-Channel 24MHz features:
- 8 channels
- 24MHz sampling frequency
- 1000M samples
- USB power
- USB 2.0 HiSpeed
- 5V supply voltage
- LED - power indicator
- LED - logic indicator 0-1 on channel 1
- USB connection
You can change the sampling frequency by hand: 24MHz, 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500kHz, 250kHz, 200KHz, 100KHz, 50KHz, 25KHz.
Works with TTL levels: low level from -0.5V to 0.8V and high level from 2V to 5.25V.

UT363 mini wind speed and temperature meters. UT363 measures wind speeds up to 30 m/s (108 km/h)

This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed.

Compact instrument that measures the speed of rotation with a visible red light beam from a powerful LED. The high intensity class II laser measures wide measurement range and high resolution, from 2.5 to 99.999 RPM (Revolutions per Minute)

5 Digits Mechanical Pull Stroke Counter features:
Product Name: Pull Counter Model: D67-F Digit Display: 5 Range: 0-99999 Counting speed: 200 times / min   Transmission ratio: 1:1   Zero return mode: Rotary    External Material: Plastic, Metal; Color: Black Total Size: 8 x 4.7 x 3.2cm/ 3' x 1.9'' x 1.3'' (L*W*T) Installation size:38×30 mm Spring Size: 2.5 x 0.4cm/ 1'' x 0.16''(L*D) Net Weight: 77g Package Content: 1 x Pull Counter,1 x Spring