20x Ceramic Capacitor 22pF 50v 2,54

Definition of the Hall effect: When a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicularly to the direction of current flow, a voltage, called the Hall voltage, proportional to the magnetic field, and the current appears on the side faces of the bar.
This voltage is proportional to the speed of movement of the charge carriers, It is considerably higher in semiconductor materials than in metal conductors. Magnetic Sensor Characteristic: - Input Voltage: 3.8-30VDC - Output current: 40mA
High output current capacity -40 mA maximum absolute
Quad-Hall design virtually eliminates static mechanical effects
Magnetic compensated temperature - Digital current sinking output

PAM8403 2x3W Digital Amplifier Channel Stereo features:
- Up to 3W in each channel
- Chip: PAM8403
- Power supply: 5V
- Power: 2 outputs of 3 watts each
- Measures: 21x18 mm
- Suitable impedance speakers: 4 Ohm

Capsule Electret Condenser Microphones 9.5 MIC features:
- Measures: 9.7 x 6.7mm
- Impedance: 1.5kΩ
- Working current: 0.5mA
- Working voltage: 4.5V (1.5-10V)
- Bandwidth: 50 ... 16000Hz
- Signal to noise ratio: ‰¥58dB
- Sensitivity: -42 ± 3dB
- Sensitivity tolerance: ± 3dB
- Distance between terminals: 2.54mm

- Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base
- This module is very similar to HM-10 module
- Bluetooth protocol: Bluetooth V4.0 BLE specification
- Ultra-low power consumption, in 90uA standby mode
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features:

- Chipset based on CC2541
- Bluetooth Class 2
- Industrial level Bluetooth module SPP
- Flash 256Kb
- Integrated chip antenna
- Power supply: + 3.3 VDC 50 mA
- Working temperature: -5 C to + 60 C
- Operating frequency: 2.4 GHz ISM Band
- Modulation method: GFSK (Gaussian Frequency Shift keying)

15x Electrolytic Capacitor 10uF 50V 105º C PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 10uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units

Lot of 65 Male-Male jumper cables. Characteristic: -No soldering required
-You can easily modify or revise the circuits
-Quantity: 65 cables of different lengths and colors
-Cable lengths: 120mm, 150mm, 200mm, 240mm

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

LED 10-Segment Bar Graphics Display Red features:
- Bargraph LED display
- Number of segments: 10
- Size: 5mm - Dimensions: 25x10mm
- Material GaAsP / GaP
- Color: red
- Wavelength: 635 nm
- Vf / forward /2.1 V
- I fw / forward / 30 mA
- Iv / Ifw = 20mA / 4 mcd
- Number of terminals: 20