Arduino

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.
Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features:
- Supply voltage: 5V (4.5V-6V)
- Consumption: typical 30 mA, (35 mA max)
- Interface: VCC, GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED measurement indicator in progress
- Frequency: 40 kHz for 200 μs
- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic
- Transparent color
- Includes screws

Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 ° C to 125 ° C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
             - Vcc red
             - Yellow digital output
- Inocidable steel
- Cable length: 3m

5.8GHz Doppler Radar Motion Sensor features:
- Microwave motion detector module
- The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications.
- High resistance to radio-frequency interference
- Frequency: 5.8GHz
- Operating Voltage: 3.3V - 20V TTL 3.3V
- Standby Current: 3mA
- Detection Range: 3-8 meters, 360 degrees
- Power of Output: 2mW
- Dimensions: 32x23 mm
- R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k
- R9 - for sensitivity adjustment

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

The meter built on the basis of a water rotor and a Hall effect sensor
Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features:
- Working voltage range: DC 5 ~ 18 V
- Allow pressure: water pressure below 1.75Mpa
- Accuracy (flow-pulse output): ± 1 ~ 30 l / min
- Use temperature: ‰ ¤ 80 ° C
- Load capacity: ‰ ¤ 10 mA (5Vdc)
- Operating humidity: 35% ~ 90% RH (frost free)
- Temperature: -25 ~ + 80 ° C
- Outlet diameter: 1/2 "
- Red wire: positive supply
- Wire Black: negative power supply
- Yellow Cable: signal output
- Color: black
- Size: 6.2x3.6x3.4 cm

This module includes the component BME280 that is translated into a digital signal.
The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.
Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features:
- Interfaces:
- I2C (up to 3.4 MHz)
- SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
- Temperature: -40ºC to + 85ºC
- Humidity: 0-100%
- Pressure: 300-1100 hPa
- Resolution of the measures:
- Temperature: 0.01ºC
- Humidity: 0.008%
- Pressure: 0. 18Pa
- Accuracy of the measures:
- Temperature: +/>

The MAX9812 is a sound amplifier specially designed to treat the signal coming from microphones.
We can use it together with Arduino to measure sound from a processor like Arduino.
When we saw the modules with microphone we commented that, in general, the signal generated is too low to be registered correctly.
If we want to be able to measure sounds, we will have to amplify the signal. The MAX9812L has single / dual inputs, fixed gain of 20dB, bandwidth of 400 kHz, low noise and low signal distortion 0.015% THD.
There are two models, its supply voltage is 2.7V to 3.6V.
We can use the sensors with MAX9812 for applications that require measuring the intensity or frequency of the sound.

Inductive Proximity Sensor PL-05N NPN Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05N 5mm with NPN output features:
- Manufacturer: Fotek,
- Square Type,
- Sensing distance: 5mm,
- Operating voltage: 10 - 30 VDC,
- Response frequency: 800Hz,
- Output method: NPN, 150mA load,
- Hysteresis: <10% of sensing distance,
- Protection degree: IP67,
- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,
- Body dimension: 30.5x17.9x10.2mm (LxWxH),
- Mounting Method: Flush,
- Sensing Direction: Horizontal,
- Materia Housing: High-impact plastic,
- Screw hole: 3.2mm, Pitch: 10.5mm,

Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA.
100% compatible UNO module.
Characteristic:
- Operating voltage: 3.3-5 VDC
- Output voltage: 0-1 VDC
- 3-pin connector:
- OUT: output signal
- VCC: Supply voltage
- GND: Ground connection - Test accuracy: ± 1UV INDEX
- Current: 0.06mA (typical), 0.1mA (maximum)
- Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds
- Operating temperature: -20ºC - + 85ºC
- Size: 19.80 x 15mm

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

The module uses a 24-bit high precision A / D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.