Fibersilk Metallic Filamento 1.75mm 0.85kg Turquoise color turquesa

This detection module that allows you to detect your heart rate and blood oxygen level from your Arduino project. You can monitor your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply press the sensor with your finger and wait for the reading of hemoglobin (Spo2), heart rate and Perfusion Index (PI%). It is a solution as an integrated heart rate sensor and pulse oximetry, which includes two LEDs, a photodetector and is optimized for analog low noise optics.

Screen OLED 0.96" B 128x64 Yellow-Blue SPI/I2C features:
- Oled 0.96 "128 * 64 pixel display
- One yellow line and 3 blue lines
- Drive IC model SDD1306
- Power supply: 3V-5.5V
- View angle: 160 degrees
- SPI interface (I2C can be changed)
- Low consumption 0.08W
- Temperature usage: -20 to 70 ºC
- PCB board dimension: 32 x 32 mm
- OLED technology offers high contrast, significantly improves black on the screen and energy efficiency - very low consumption of energy.

45-centimetre crocodile cables to USB.  They come in a pair of two cables, one red and the other black, connected to a male USB connector.

9g digital servo new version of SG90.
POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque.
It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features:
Weight: 9g
Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v)
Gear type: POM with carbon fiber
Operating speed: 0.1sec /60degree (4.8v)
Temperature range: 0„ƒ_ 55„ƒ
Dead band width:1us
servo wire length: 25 cm
Servo Plug: JR (Fits JR and Futaba)
servo arms &screws included and fit with Futaba servo arm

Premium Bobina para Impresora 3D

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Resistor 220 Ohm 5% 0,25W 1/4W features:
-220 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features:
- Channels: 8 (independent protected with Optocouplers)
- Supply Voltage Vcc: 5Vdc
- Output Current: 10A
- High trip min 3.3V input IN1. ..IN8
- Relay activation current: 5 ~ 10mA
- Isolation: Yes
- Indicator LED: For each channel
- Dimensions: 55x 139mm
- Weight: 120g
COM GND jumper input: connects GND optocouplers and GND of the circuit