Female Strip 40 Short Pins Female Strip 40 Short Pins features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Pasante - Quantity: 1 unit of strips of 40 female pins each Code K0139 Available Price €0.57
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.48
GPS Module GY-GPS6MV2 NEO6MV2 EEPROM with Antenna It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip. The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed. Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC - Operating current: 45 mA - Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds - Navigation update: 5 Hz max. (1 Hz default) - Capture time: at the beginning 27s, in operation 1s - Operating temperature: -40 ° C - + 85 ° C - separate GPS antenna 18x18 mm - Size: 22x30x13 mm Code M0071 ✗ Out-of-Stock Price €13.14
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €7.84
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €2.88
Solar Power Management Module, for 6V~24V Solar Panel The solar power management module is designed for 6V~24V solar panel. It can charge Li 3.7V battery through solar panel or USB connection, and provides 5V/1A regulated output. Code WV002 Available Price €10.70
Solar Panel DIY 4V 30mA DIY mobile photovoltaic panel with working voltage of 4V and max. working current of 30mA. Code A0061 Available Price €2.06
6V 4.5W DIY Solar Panel 6V 4.5W DIY Solar Panel features: - Mobile DIY System Photovoltaic Charger Cell -Work Voltage: 6V -Power output: 4.5W -Working current: 0-750mA -Product size: 165x165x3 mm Code A0063 ✗ Out-of-Stock Price €10.65
Solar panel controller 3.7V - 2A Lithium battery charge, discharge with light control 3.7V - 2A solar panel controller, charging, discharging lithium battery with lighting control with output from 2.5 V to 4.2 V. Integrate PWM suspension float. Characteristic: - Charging current: 2A - Compatible battery type: Li-ion - Type: 3.7V single cell lithium battery solar controller - PWM suspension float with integrated maintenance charge. - Avoid overcharging the lithium battery. - Battery type included: None - Charging voltage output limit: 4.2V - Low voltage drip charging of the battery: 2.5V - Over discharge voltage: 2.8V Order of use: 1 ) LED lights connected to "+ OUT", correspond to positive and negative. Code A0095 ✗ Out-of-Stock Price €9.00
12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell Suitable for a small solar power system, etc. 12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell features: - Working voltage: 12V - Output power: 1.5W - Product size: 115x 85x 3 mm Applications: - Charge cell phones - Home lighting - DIY solar powered toys Code A0070 Available Price €4.04
Solar Panel 6V 5W Waveshare solar panel with working voltage of 18V and output power of 10W and maximum working current of 570 mA. Includes polysilicon cells. The panel is placed in a rigid, high-strength frame. Code WV003 ✗ Out-of-Stock Price €21.45
6V 4.5W DIY Solar Panel with cable The DIY mobile photovoltaic panel charger with working voltage of 6V and output power of 3W. The board is supplied with soldered cables. Code A0179 Available Price €8.22
Solar panel DIY 6V 1W with cable The DIY mobile photovoltaic panel charger with working voltage of 6V and output power of 1W. The board is supplied with soldered cables. Code A0180 Available Price €5.74
6V 2W Solar Panel Do-it-yourself Mobile Photovoltaic Charger Cell Suitable for a small solar power system, etc. 6V 2W Solar Panel Do-it-yourself Mobile Photovoltaic Charger Cell features: - Working voltage: 6V - Output power: 2W - Product size: 136x 110x 3 mm Applications: - Charge cell phones - Home lighting - DIY solar powered toys Code A0071 Available Price €4.92
Solar panel DIY 6V 1.1W 200mA Solar panel DIY 6V 1.1W 200mA features: - DIY Mobile Photovoltaic Charger - Working Voltage: 6V - Output Power: 1.1W - Working current: max. 200 mA - Product size: 112x 84x3 mm Code A0064 Available Price €4.88
Solar Power Management Module, for 6V~24V Solar Panel The solar power management module is designed for 6V~24V solar panel. It can charge Li 3.7V battery through solar panel or USB connection, and provides 5V/1A regulated output. Code WV002 Available Price €10.70
Solar Panel DIY 4V 30mA DIY mobile photovoltaic panel with working voltage of 4V and max. working current of 30mA. Code A0061 Available Price €2.06
6V 4.5W DIY Solar Panel 6V 4.5W DIY Solar Panel features: - Mobile DIY System Photovoltaic Charger Cell -Work Voltage: 6V -Power output: 4.5W -Working current: 0-750mA -Product size: 165x165x3 mm Code A0063 ✗ Out-of-Stock Price €10.65
Solar panel controller 3.7V - 2A Lithium battery charge, discharge with light control 3.7V - 2A solar panel controller, charging, discharging lithium battery with lighting control with output from 2.5 V to 4.2 V. Integrate PWM suspension float. Characteristic: - Charging current: 2A - Compatible battery type: Li-ion - Type: 3.7V single cell lithium battery solar controller - PWM suspension float with integrated maintenance charge. - Avoid overcharging the lithium battery. - Battery type included: None - Charging voltage output limit: 4.2V - Low voltage drip charging of the battery: 2.5V - Over discharge voltage: 2.8V Order of use: 1 ) LED lights connected to "+ OUT", correspond to positive and negative. Code A0095 ✗ Out-of-Stock Price €9.00
12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell Suitable for a small solar power system, etc. 12V 1.5W Do-it-yourself Mobile Solar Panel Photovoltaic Charger Cell features: - Working voltage: 12V - Output power: 1.5W - Product size: 115x 85x 3 mm Applications: - Charge cell phones - Home lighting - DIY solar powered toys Code A0070 Available Price €4.04
Solar Panel 6V 5W Waveshare solar panel with working voltage of 18V and output power of 10W and maximum working current of 570 mA. Includes polysilicon cells. The panel is placed in a rigid, high-strength frame. Code WV003 ✗ Out-of-Stock Price €21.45
6V 4.5W DIY Solar Panel with cable The DIY mobile photovoltaic panel charger with working voltage of 6V and output power of 3W. The board is supplied with soldered cables. Code A0179 Available Price €8.22
Solar panel DIY 6V 1W with cable The DIY mobile photovoltaic panel charger with working voltage of 6V and output power of 1W. The board is supplied with soldered cables. Code A0180 Available Price €5.74
6V 2W Solar Panel Do-it-yourself Mobile Photovoltaic Charger Cell Suitable for a small solar power system, etc. 6V 2W Solar Panel Do-it-yourself Mobile Photovoltaic Charger Cell features: - Working voltage: 6V - Output power: 2W - Product size: 136x 110x 3 mm Applications: - Charge cell phones - Home lighting - DIY solar powered toys Code A0071 Available Price €4.92
Solar panel DIY 6V 1.1W 200mA Solar panel DIY 6V 1.1W 200mA features: - DIY Mobile Photovoltaic Charger - Working Voltage: 6V - Output Power: 1.1W - Working current: max. 200 mA - Product size: 112x 84x3 mm Code A0064 Available Price €4.88