DC 15V Analog Panel Voltmeter 0 to 15V Round

It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0.

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

DC 10A Analog Panel Ammeter 0 to 10A features:
- DC 10A Ammeter Instrument Analog Amperage meter panel with shunt
- Type: Analogue ammeter
- Range: DC 0-10A
- Accuracy: class 2.5
- Size: 51 × 51 × 46mm
- Complete with screws for simple DIY installation
- This meter has a built-in bypass, does not need external derivation

Servos Tester features:
- 3-Channel Tester
- For Electronica Arduino

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets.
The voltage and current are shown successively.
Current and Voltage Meter Tester features:
- Operating range:
       - Voltage 3 - 7,5V
       - Current 0 -3A
- Resolution: 10mV 1mA
- Error: <± 1.5%%
- Dimensions: 5.2 x 2 x 1.5 cm

This module is a three-way switch (COM, NO and NC) that uses the intensity of the ambient light to directly control the output load. Its adjustment potentiometer allows you to change the sensitivity and set the threshold for starting the relay. The relay is energized when it is darker than the threshold.
The optical isolation relay effectively protects the chip and ensures better performance.
This module is used for light detection, brightness detection , control of lamps and automatic equipment. Characteristic: - Channels: 1
- Supply voltage: 12VDC
- Output load capacity: 250V 10A AC / 30V 10A DC
- Relay activation current: & gt; 100mA
- Insulation: Yes
- Indicator LED: Green and Red
- PCB size: 5x2.6 cm / 1.96x1.02 "