DC 15V Analog Panel Voltmeter 0 to 15V

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

A bridge rectifier KBPC5010 is an array of electronic components, which is present in most voltage sources; The bridge is formed regularly by 4 diodes, connected in a specific way, and its function is to transform the alternating current to direct current. Bridge Rectifier 50A/1000V KBPC5010 features:
- Metal housing
- Type of diode: bridge rectifier
- Type of bridge: a phase
- Maximum driving voltage: 1000 V
- Maximum driving current: 50 A
- Peak inverse voltage: 1 kV
- Direct voltage Vf (max.) To If: 1.1V @>

High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side.
Ideal for your Arduino projects, but can also be used with other microcontrollers.
Matrix Membrane Keyboard 4x4 Modulo features:

- Rating circuit, Max: DC 35V 100 mA
- Cable length: 85 mm
- Dupont 8 pin connector
- Specific insulation: 100 M Ohm, 100V
- Useful life: + 1 million uses
- Contact parting:

This module is a three-way switch (COM, NO and NC) that uses the intensity of the ambient light to directly control the output load. Its adjustment potentiometer allows you to change the sensitivity and set the threshold for starting the relay. The relay is energized when it is darker than the threshold.
The optical isolation relay effectively protects the chip and ensures better performance.
This module is used for light detection, brightness detection , control of lamps and automatic equipment. Characteristic: - Channels: 1
- Supply voltage: 12VDC
- Output load capacity: 250V 10A AC / 30V 10A DC
- Relay activation current: & gt; 100mA
- Insulation: Yes
- Indicator LED: Green and Red
- PCB size: 5x2.6 cm / 1.96x1.02 "

- Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base
- This module is very similar to HM-10 module
- Bluetooth protocol: Bluetooth V4.0 BLE specification
- Ultra-low power consumption, in 90uA standby mode
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features:

- Chipset based on CC2541
- Bluetooth Class 2
- Industrial level Bluetooth module SPP
- Flash 256Kb
- Integrated chip antenna
- Power supply: + 3.3 VDC 50 mA
- Working temperature: -5 C to + 60 C
- Operating frequency: 2.4 GHz ISM Band
- Modulation method: GFSK (Gaussian Frequency Shift keying)

Compact instrument that measures the speed of rotation with a visible red light beam from a powerful LED. The high intensity class II laser measures wide measurement range and high resolution, from 2.5 to 99.999 RPM (Revolutions per Minute)

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

It allows controlling many different types of engines: - Up to 4 bidirectional current motors
- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos.                   L293D Motor Drive Shield Expansion Board features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A (650mA)
- Logic voltage: 5V
- Controller L293D
- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.
Pull-down resistors keep the motors off during startup.