USB Digital Power Voltmeter Tester Amps Device to measure the power consumption of any device powered by USB: phones, chargers, USB disks, consoles, tablets ...USB Digital Power Voltmeter Tester Amps features:- Operating range: voltage 3.5 - 9V- Current 0 -3A- Resolution: 10mV 1mA- Error: <± 1.5%- Dimensions: 60 x 23 x 19mm Code K0083 Available Price €5.95
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.49
5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm Code R0038 Available Price €2.95
Cables for Multimeter 2 Cables for 1M Multimeter Meter features: - Voltage 1000V, 10A CAT III- Total length 110cm- Red and black colors Code K0012 Available Price €3.95
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 Available Regular price €11.95 -€2.40 Price €9.55
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.08
Traffic light LED red yellow green 5V display module Arduino Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects. Code M0231 Available Price €2.39
Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY features: - Mounting kit - Ceramic Peltier Cell 12V TEC1-12706 - Heatsink 12x10x25mm (hot side) - Heatsink 60x40x25mm - Color black or silver - Thermal insulation 70x65mm for cell - Fan 12V 90x90x25mm with grille - Thermal paste 0.5g - Screws - Peltier effect cell model TEC1-12706, 12v, max. 60w and 6A, with a temperature difference between their faces of up to 67ºC - Max Power: 60w - Voltage: 12v - Max Voltage: 15.2v - Max Current: 6A - Temperature Variation: Code M0059 Available Price €18.79
DIY Paste Dissipative Fan Kit for Ceramic Peltier Cell TEC1-12706 Characteristic: - Heatsink 12x10x25mm (hot side) - Heatsink 60x40x25mm (black or silver color) - 70x65mm thermal insulation for cell - Fan with grid 12V 90x90x25mm - Thermal paste 0.5g - Screws - Kit does not include: Peltier cell Ceramic TEC1-12706 12V Code M0060 Available Price €15.99
Fan 12V 2x Cable 50x50x15 3D Printer Reprap Fan 12V 2x Cable 50x50x15 3D Printer Reprap features: - Voltage: 12V - Speed: 7000rpm ± 10% - Screw diameter: 4.5mm - Time lifespan: 50,000 hours - Operating temperature: -10 ° C to 70 ° C - Cable length: 28cm - Dimensions: 50mm x 50mm x 10mm Code I0120 Available Price €2.09
Peltier Thermoelectric Kit with Cooling Fan 12V 72W Kit includes heatsinks, thermal insulation for peltier cell, fan with grille, thermal paste, screws and TEC1-12706 12V ceramic peltier cell. Code M0227 Last items in stock Price €31.95
Fan Black 12V 2x PC CPU Cables Characteristic: - Voltage: 12V - Consumption: 0.3A - Screw diameter: 4mm - Product duration in operation: 30000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 14.5cm - Dimensions: 92mm x 92mm x 25mm Code I0054 Available Price €2.89
Fan 12V 2x Cables 3D Reprap Printer Fan 12V 2x Cables 3D Reprap Printer features: - For Prusa RepRap 3D Printer - Voltage: 12V - Consumption: 90mA - Speed: 7000rpm ± 10% - Noise level: 25dB ± 10% - Screw diameter: 3.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 28cm - Dimensions: 30mm x 30mm x 10mm Code I0045 Available Price €1.59
Fan 12V 2x Cables PC CPU case Fan 12V 2x Cables PC CPU case features: - Voltage: 12V - Consumption: 0.28A - Screw diameter: 3.5mm - Life time useful: 30,000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 24.5cm - Dimensions: 80mm x 80mm x 15mm Code I0055 Available Regular price €3.49 -€0.90 Price €2.59
Fan 5V 2x Cable 50x50x15mm Fan 5V 2x Cable 50x50x15mm features: - Voltage: 5V - Speed: 7000rpm ± 10% - Screw diameter: 4.5mm - Time lifespan: 50,000 hours - Operating temperature: -10 ° C to 70 ° C - Cable length: 28cm - Dimensions: 50mm x 50mm x 15mm Code I0169 Available Price €2.09
Fan 12V 2x 3D Printer Cables Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 65mA - Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10% - Screw diameter: 4.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 11cm - Dimensions: 40mm x 40mm x 10mm Code I0026 Available Price €1.59
Mini Fan 12V 2x 3D Printer Cables Mini Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 80mA - Speed: 2600rpm +/- 10% - Temperature operating: -10 ° C to 65 ° C - Cable length: 12cm - Dimensions: 25mmx 25mm x 10mm Code I0027 Available Price €1.59
Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY Kit Peltier Cell 12V TEC1 12706 Fan Thermal Paste DIY features: - Mounting kit - Ceramic Peltier Cell 12V TEC1-12706 - Heatsink 12x10x25mm (hot side) - Heatsink 60x40x25mm - Color black or silver - Thermal insulation 70x65mm for cell - Fan 12V 90x90x25mm with grille - Thermal paste 0.5g - Screws - Peltier effect cell model TEC1-12706, 12v, max. 60w and 6A, with a temperature difference between their faces of up to 67ºC - Max Power: 60w - Voltage: 12v - Max Voltage: 15.2v - Max Current: 6A - Temperature Variation: Code M0059 Available Price €18.79
DIY Paste Dissipative Fan Kit for Ceramic Peltier Cell TEC1-12706 Characteristic: - Heatsink 12x10x25mm (hot side) - Heatsink 60x40x25mm (black or silver color) - 70x65mm thermal insulation for cell - Fan with grid 12V 90x90x25mm - Thermal paste 0.5g - Screws - Kit does not include: Peltier cell Ceramic TEC1-12706 12V Code M0060 Available Price €15.99
Fan 12V 2x Cable 50x50x15 3D Printer Reprap Fan 12V 2x Cable 50x50x15 3D Printer Reprap features: - Voltage: 12V - Speed: 7000rpm ± 10% - Screw diameter: 4.5mm - Time lifespan: 50,000 hours - Operating temperature: -10 ° C to 70 ° C - Cable length: 28cm - Dimensions: 50mm x 50mm x 10mm Code I0120 Available Price €2.09
Peltier Thermoelectric Kit with Cooling Fan 12V 72W Kit includes heatsinks, thermal insulation for peltier cell, fan with grille, thermal paste, screws and TEC1-12706 12V ceramic peltier cell. Code M0227 Last items in stock Price €31.95
Fan Black 12V 2x PC CPU Cables Characteristic: - Voltage: 12V - Consumption: 0.3A - Screw diameter: 4mm - Product duration in operation: 30000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 14.5cm - Dimensions: 92mm x 92mm x 25mm Code I0054 Available Price €2.89
Fan 12V 2x Cables 3D Reprap Printer Fan 12V 2x Cables 3D Reprap Printer features: - For Prusa RepRap 3D Printer - Voltage: 12V - Consumption: 90mA - Speed: 7000rpm ± 10% - Noise level: 25dB ± 10% - Screw diameter: 3.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 28cm - Dimensions: 30mm x 30mm x 10mm Code I0045 Available Price €1.59
Fan 12V 2x Cables PC CPU case Fan 12V 2x Cables PC CPU case features: - Voltage: 12V - Consumption: 0.28A - Screw diameter: 3.5mm - Life time useful: 30,000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 24.5cm - Dimensions: 80mm x 80mm x 15mm Code I0055 Available Regular price €3.49 -€0.90 Price €2.59
Fan 5V 2x Cable 50x50x15mm Fan 5V 2x Cable 50x50x15mm features: - Voltage: 5V - Speed: 7000rpm ± 10% - Screw diameter: 4.5mm - Time lifespan: 50,000 hours - Operating temperature: -10 ° C to 70 ° C - Cable length: 28cm - Dimensions: 50mm x 50mm x 15mm Code I0169 Available Price €2.09
Fan 12V 2x 3D Printer Cables Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 65mA - Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10% - Screw diameter: 4.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 11cm - Dimensions: 40mm x 40mm x 10mm Code I0026 Available Price €1.59
Mini Fan 12V 2x 3D Printer Cables Mini Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 80mA - Speed: 2600rpm +/- 10% - Temperature operating: -10 ° C to 65 ° C - Cable length: 12cm - Dimensions: 25mmx 25mm x 10mm Code I0027 Available Price €1.59