Power supply DC 12V 3A 36W

USB SALEAE is an 8-channel logic analyzer without memory, a maximum sampling speed of 24MHz (depends on the PC and the use of the USB bus).
It allows you to record and display digital data read on the computer.
Logic Analyzer 8-Channel 24MHz features:
- 8 channels
- 24MHz sampling frequency
- 1000M samples
- USB power
- USB 2.0 HiSpeed
- 5V supply voltage
- LED - power indicator
- LED - logic indicator 0-1 on channel 1
- USB connection
You can change the sampling frequency by hand: 24MHz, 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500kHz, 250kHz, 200KHz, 100KHz, 50KHz, 25KHz.
Works with TTL levels: low level from -0.5V to 0.8V and high level from 2V to 5.25V.

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Connector Jack 2.1x5.5mm Power Supply DC Male features:
- Ideal for connecting without welding
- It has two screws in the tip for positive and negative cable screwdriver

Limit Switch with Lever 

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

W5100 Mini Network Module Ethernet Shield Arduino features:
- Shield Ethernet for Arduino and compatible boards based on the Wiznet W5100 chip
- Provides a simple mode to connect your module to the local network and the internet
- Compatible with the official Arduino Ethernet library
- With this shield you can build a web server
- It can be used as a server or as a client - Controller: Wiznet W5100
- Supports TCP and UDP protocols
- Supports up to 4 simultaneous connections
- Compatible with all versions of Arduino: UNO, mega 1280/2560
- Dimensions: 50 x 25x 25mm

Relay Module DC 5V 10A 2 Channel Low/High Trigger features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- It has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)