Mounting Bracket for Nema Engine 17 42mm

Car Robot Tire Wheel Smart Car features:
- Dimensions of the wheel:
   - Diameter: 65mm
   - Width: 26 mm
- Quantity: 1 unit

Product Category: Bipolar Transistor, PNP
BC557B 50V PNP Transistor 100mA 0.1A TO-92 features:

- Package / Case: TO-92
- Quantity: 25 units
- Collector-base voltage VCBO: 50V
- Collector-emitter voltage VCEO: 45V
- VEBO emitter-base voltage: 6V
- Continuous collector current: 100mA
- DC MAX collector current: 200mA
- Maximum power dissipation: 500mW

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Connectors 15x BLS04 Female / Female 4 Pins RoHS Single Row features:
- Step between pins: 2.54 mm
- Manufacturer: Maritex
- Number of connections: 4 in a single row
- Type: Female / Female
- RoHS standard

The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.
This product offers more flexible options for users.
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:
- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.
- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.
se high quality MOSFET, better cooling and more stable.

Power Supply DC 5V 6A 30W features:
- Supply voltage: 110 / 230V AC
- Output voltage: 5V DC - Output amperage: 6A
- Power at 5V: 30W
- Dimensions: 110mm x 78mm x 36mm

- It consists of a 20-character, 4-row display
- The display is compatible with the controller HD44780 and integrates the module so you can use it through the I2C protocol without any problem
- Only two pins are needed for communication, SDA and SCL
- Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32
PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F
- It can be changed to any between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2
20x4 2004 LCD display PCF8574T I2C Backlit Blue features:

- LCD screen, 20 characters and 4 lines
- 5V power supply
- HD44780 compatible controller

3x DC PCB Socket Connector 5.5 x 2.1 features:
- Type: DC female jack
- Diameter of the pin: 2,1mm
- Diameter of the connector: 5.5mm
- Quantity: 3 units