Soldering Station 48W

Momentary Switch Push Button Black N/O 7mm features:
- Momentary pushbutton N/O (normally open)
- Black button
- Dimensions approx. 7 mm x 27 mm
- Recessed with nut and washer
- Load current (supported): 1A to 230V / 2A to 125V
- Drill to embed: 7 mm +/- 0.2
- Operating temperature: -55ºC to + 85ºC

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Manufacturer: Taiwan Semiconductor 5x Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 features:
- Type Output: fixed
- Voltage Output: 3.3 V
- Output Current: 800mA
- Max input voltage: 12V
- Operating temperature: -20C to + 85ºC
- Encapsulated: SOT223
- Dropout Voltage Vdo: 1.3V (1A)
- Quantity: 5 units

The components of the ratchet crimping pliers are made of special steel.
Designed according to human engineering factors, 50% energy can be saved when crimping.
AWG: 28 - 18
Length: 190 mm (approx.)
Crimp capacity: 0.1 - 1.0 mm².
For 2.54 mm 3.96 mm KF2510 connector weight 0.35kg

60/40 Tin Lead Solder Wire Soldering Flux Sn60/Pb40 2.5% 1mm 50g features:
- 50gr. 1mm diameter welding wire. 60% tin and 40% lead.
- Fusing temperature 183°C/190°C.
- Alloy: Sn60 Pb40
- Flux 2.5%
- Quantity: 1 unit

Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.56mm features:
- 100gr. 0.56mm diameter welding wire. 60% tin and 40% lead
- Fusing temperature 183 „ƒ / 190 „ƒ
- Alloy Sn60 Pb40
- Flux 2.5%
- Quantity: 1 unit

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg features:
A compound for etching of printed circuit boards and pickling of copper. An ideal alternative to ferric chloride. It is readily soluble and does not crystallize from the solution. It etches evenly, ensures the sharpness of contours and minimizes undercutting. Usage: Dissolve the preparation in 0.5 l of water at a temperature of 50°C. Perform etching at 40°C (max. 50°C). Bath movement ensures quicker etching. The etching solution must not be stored in hermetically sealed containers due to the risk of developing overpressure and cracks.