ZD-8906 Digital Soldering Station 30W

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

- HC-05 Bluetooth transceiver module with base
- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.
- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.
Bluetooth Transceiver Module HC-05 Wireless features:
- Chipset CSR BC417
- 3.6 to 6 Vdc power supply
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Reach approx. 10m
- Security: Authentication and encryption.
- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

Fan 12V 2x Cables 3D Reprap Printer features:
- For Prusa RepRap 3D Printer
- Voltage: 12V
- Consumption: 90mA - Speed: 7000rpm ± 10%
- Noise level: 25dB ± 10%
- Screw diameter: 3.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 28cm
- Dimensions: 30mm x 30mm x 10mm

TP4056 Module Lithium Battery Charger with Protection features:
- TP4056 Li-Ion Micro USB Charger
- Upgraded version of previous TP4056
- Micro USB connection to charge directly from the PC
- Ideal for 18650 batteries
- Based on the TC4056A regulator
- Input Voltage: 4.5V - 5.5V DC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Overvoltage protection 4.2V
- Over discharge protection 2.4V
- LED indicator: charging blue, charging red
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Overcurrent protection: 3A
- Measurements 26 x 19 x 5 mm
- Possibility of current change through Rprog

Voltmeter Ammeter 100V 50A Digital DC Red Blue features:
- Supply voltage: 4.5V to 30V
- Voltage measurement range: 0V to 100V (± 1%)
- Min voltage resolution: 0.1V
- Current measurement range: 0A to 50A (± 1%)
- Min current resolution: 0.1A
- Operating current: 5mA to 15mA
- Display: Red LED color (Voltage) and Blue LED color (Intensity)
- Includes reverse polarity protection
- Measurement refresh time: 500ms
- Screen dimensions: 48 x 29 mm
- Recessed hole: 45.5 x 26.5 mm
- Depth: 21 mm
- Cable length: 150 mm
- Operating temperature: - 10ºC to 65ºC
- No battery needed
- Dual panel with voltmeter and digital ammeter Useful links for Arduino />