M3x30 Nylon Hexagonal Splitter M3x30 Nylon Hexagonal Splitter features: - Material PA66 - Type: female / female - Thread size / inner diameter M3 - Body length: 30mm - Color: white Code H0087 Available Price €0.24
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.12
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Available Price €7.43
Display OLED 0.96" 128x64 White I2C 4 Pin Display OLED 0.96" 128x64 White I2C 4 Pin features: - Interface: I2C (logical level 3.3V) - Resolution: 128x64 - Angle of view:> 160 degree - Screen color: white - Screen Dimension: 2.43cm / 0.96 " - IC Controller: SSD1306 - Power supply: 3.3V - 5VDC - Operating temperature: -20 ° C - 70 ° C - Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 " - Application: smart watch, MP3, thermometer , instruments, DIY projects, etc ... - It is an OLED display module with white display and with a dot matrix of a resolution 128x64 and an IC2 interface. - The display includes the IC driver SSD1306 128 x 64 OLED / PLED Segment / Common Driver. Code P0091 Available Regular price €5.37 -€2.51 Price €2.86
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.02
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
Arduino Uno R3 Arduino UNO is the best board to start your experience with electronics and programming. If this is your first experience with the platform, UNO is the most robust board you can start with. UNO is the most widely used and documented board in the entire Arduino family. Its power ensures ATmega 328p microcontroller, the board is equipped with 14 digital pins, and 6 analog Code BAR66 ✗ Out-of-Stock Price €21.98
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €79.00
Nano V3.0 Terminal Block Adapter Nano V3.0 Terminal Block Adapter features: - Nano V3.0 Atmega328P adapter with soldered connectors - PCB dimensions: 53mm x 35mm Code B0024 Available Price €3.71
Arduino Pro PORTENTA H7 The Arduino Portenta H7 represents a new family of chips designed for IoT applications. The board uses the STM32H747 microcontroller equipped with Cortex-M7 and Cortex-M4 cores, which allows it to run programs written in Arduino®, MicroPython or JavaScript. In addition, the Arduino Portent H7 is characterised by high performance and at the same time energy efficiency. Code ABX42 Available Price €104.12
L293D STM Module Expansion Board 2 Motors - 25V/0.6A The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V. Code M0108 Available Price €3.79
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Last items in stock Price €7.43
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
Extension Board Shield Nano V3.0 ATmega328P Extension Board Shield for Arduino Nano V3.0. Code B0025 Available Price €2.44
Arduino Edge Control A remote monitoring and control solution, optimised for outdoor environments. Collect real-time data from smart sensors and leverage everything to the edge, in your smart farm management. Code AKX034 Backorder Price €179.00
Screw Shield V2 for Arduino UNO Screw Shield V2- Arduino ScrewShield UNO features: Screw Shield V2 allows: - Being punctured directly to an Arduino Uno- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0172 Available Regular price €4.09 -€1.00 Price €3.09
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €79.00
Nano V3.0 Terminal Block Adapter Nano V3.0 Terminal Block Adapter features: - Nano V3.0 Atmega328P adapter with soldered connectors - PCB dimensions: 53mm x 35mm Code B0024 Available Price €3.71
Arduino Pro PORTENTA H7 The Arduino Portenta H7 represents a new family of chips designed for IoT applications. The board uses the STM32H747 microcontroller equipped with Cortex-M7 and Cortex-M4 cores, which allows it to run programs written in Arduino®, MicroPython or JavaScript. In addition, the Arduino Portent H7 is characterised by high performance and at the same time energy efficiency. Code ABX42 Available Price €104.12
L293D STM Module Expansion Board 2 Motors - 25V/0.6A The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V. Code M0108 Available Price €3.79
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Last items in stock Price €7.43
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
Extension Board Shield Nano V3.0 ATmega328P Extension Board Shield for Arduino Nano V3.0. Code B0025 Available Price €2.44
Arduino Edge Control A remote monitoring and control solution, optimised for outdoor environments. Collect real-time data from smart sensors and leverage everything to the edge, in your smart farm management. Code AKX034 Backorder Price €179.00
Screw Shield V2 for Arduino UNO Screw Shield V2- Arduino ScrewShield UNO features: Screw Shield V2 allows: - Being punctured directly to an Arduino Uno- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0172 Available Regular price €4.09 -€1.00 Price €3.09