M3x8 Nylon Screw

20x Ceramic Capacitor 100pF 50v 2,54 PCB PIC Arduino 0.022uF features:
-Type: ceramic NPO
-Tolerance: +/-5%
-Dimensions: diameter 5mm, pitch 2.54mm

10x Male-Male Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have male header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Screw Shield V2- Arduino ScrewShield UNO features:
Screw Shield V2 allows: - Being punctured directly to an Arduino Uno
- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more.

This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.
It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features:
- Input voltage: 3.3 - 5 VDC
- Multi-channel RS232 controller / receiver MAX3232
- Transmission / reception speed up to 250 kbit / s
- DB9 serial port
- Interface with four pins:
       - TX: transmission signal
       - RX: reception signal
       - VCC: Supply voltage
       - GND: connects the power cathode
- Operating temperature: -65 ° C - + 150 ° C
- UART communication
- Includes a 4-wire female / female connector for easy connection with the arduino

It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per Pin I / O 40 mA
- Flash Memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Frequency: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

Inlet Module Plug Fuse Switch 220V C14 3D Printer features:
- Voltage and current of 10A, 250V AC
- Plug type - 3 pins IEC320 C14
- Color of the red switch
- Diameter holes 40 mm
- Distance between holes 39mm
- Size 47 x 27 mm
- Total size of 58 x 50 x 34 mm

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C