Servo 9g SG92r 2.5kg 9g digital servo new version of SG90. POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque. It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features: Weight: 9g Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v) Gear type: POM with carbon fiber Operating speed: 0.1sec /60degree (4.8v) Temperature range: 0„ƒ_ 55„ƒ Dead band width:1us servo wire length: 25 cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm Code R0079 ✗ Out-of-Stock Price €3.55
Electronic Prototype ABS Plastic Black Box 100x60x25 mm Electronic Prototype ABS Plastic Black Box 100x60x25 features: - Box for electronic projects, power supply units, student projects,amplifiers, etc- Dimension 100x60x25 mm Code H0120 Available Price €1.78
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Backorder Price €3.26
Circular force sensing resistor The resistance of the sensor has a force measurement range of 0-10 kgIts resistance varies depending on how much pressure is applied to the detection area, the greater the force, the lower the resistance.Peel and stick the rubber backing on the other side of the detection area to mount.It can detect the applied force in the detection area in the range of 0g-10kg. Circular force sensing resistor features: - Detection area: 1.27cm / 0.5 inches- Output signal: passive variable resistance- Force detection range: 0 g ~ 10 kg- Length: 6 cm / 2.36 inches- Width: 1.9cm / 0.75 inches Code S0135 Available Price €7.02
DC Gear Motor and Tire Wheel for Smart Car Robot DC Gear Motor and Tire Wheel for Smart Car Robot features:- Voltage: 3 to 6 Vdc- Reduction: 1:48- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0011 Available Price €3.21
40x Female Male 10cm 40x Female Male 10cm features: - Length: 10cm - Quantity: 40 cables - Compatible with 2.54mm male connectors - High quality and good working conditions - Easy to install and use Code K0106 Available Price €1.64
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0013 Available Price €0.07
2x AAA 3V battery holder for Micro:bit Weight: 12.7g Box size: 62 * 25 * 10 mm Code PP037 Available Price €1.64
Digital finger pulse oximeter ZM-700-0 With this small and simple device, you can control your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply insert your finger and wait for the reading of haemoglobin (Spo2), heart rate and Perfusion Index (PI%). The heart rate is also graphically displayed. You can rotate the screen to see it in its 4 positions. High precision device, with low power consumption and automatic shutdown. Code H0243 Available Regular price €16.45 -€1.50 Price €14.95
Advancer Technologies MyoWare Muscle Sensor This sensor from Advancer Technologies is an improved version of the bestseller from this producer. It got several upgrades including single supply voltage of 3.1V up to 5V, polarity protection in the power pins output and RAW EMG. Code SP026 Backorder Price €62.39
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
SparkFun Pulse Oximeter and Heart Rate Sensor - MAX30101 & MAX32664 (Qwiic) This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use. Code SP030 Backorder Price €43.79
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €6.19
mmWave 24GHz Sensor - Human Static Presence Lite Human Presence Module mmWave 24GHz Sensor - Human Static Presence Lite Human Presence Module - human presence, FMCW, Configurable Underlying Parameter, Arduino support, Home Assistant, ESPHome Code SS050 Last items in stock Price €9.91
MyoWare 2.0 Muscle Sensor Basic Kit Sparkfun sensor MyoWare® 2.0 from Advancer Technologies is a newer version of this producer's bestseller. The MyoWare 2.0 muscle sensor included in this kit has been redesigned from the ground up with a new compact and easy-to-use design, and has been updated with the latest, most advanced chipset to improve sensor performance and reliability. In addition, MyoWare has developed a range of shields that work with the sensor (in our LED shield offering, displaying sensor readings as LED lights). Code SP044 Available Price €100.79
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €7.43
Gravity: Analogue heart rate monitor sensor (ECG) for Arduino The DFRobot heart rate monitor sensor (SEN0213) is used to measure the electrical activity of the heart. Code DF015 Last items in stock Price €23.93
Digital finger pulse oximeter ZM-700-0 With this small and simple device, you can control your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply insert your finger and wait for the reading of haemoglobin (Spo2), heart rate and Perfusion Index (PI%). The heart rate is also graphically displayed. You can rotate the screen to see it in its 4 positions. High precision device, with low power consumption and automatic shutdown. Code H0243 Available Regular price €16.45 -€1.50 Price €14.95
Advancer Technologies MyoWare Muscle Sensor This sensor from Advancer Technologies is an improved version of the bestseller from this producer. It got several upgrades including single supply voltage of 3.1V up to 5V, polarity protection in the power pins output and RAW EMG. Code SP026 Backorder Price €62.39
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
SparkFun Pulse Oximeter and Heart Rate Sensor - MAX30101 & MAX32664 (Qwiic) This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use. Code SP030 Backorder Price €43.79
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €6.19
mmWave 24GHz Sensor - Human Static Presence Lite Human Presence Module mmWave 24GHz Sensor - Human Static Presence Lite Human Presence Module - human presence, FMCW, Configurable Underlying Parameter, Arduino support, Home Assistant, ESPHome Code SS050 Last items in stock Price €9.91
MyoWare 2.0 Muscle Sensor Basic Kit Sparkfun sensor MyoWare® 2.0 from Advancer Technologies is a newer version of this producer's bestseller. The MyoWare 2.0 muscle sensor included in this kit has been redesigned from the ground up with a new compact and easy-to-use design, and has been updated with the latest, most advanced chipset to improve sensor performance and reliability. In addition, MyoWare has developed a range of shields that work with the sensor (in our LED shield offering, displaying sensor readings as LED lights). Code SP044 Available Price €100.79
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €5.36
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €7.43
Gravity: Analogue heart rate monitor sensor (ECG) for Arduino The DFRobot heart rate monitor sensor (SEN0213) is used to measure the electrical activity of the heart. Code DF015 Last items in stock Price €23.93