Digital Compass Magnetometer GY-271 5883 Compass is based on a QMC5883L system, which allows you to specify the direction of the earth's magnetic field. Digital Compass Magnetometer GY-271 features: 3.3V - 6V power supply voltage Current consumption of 100μA (standby 2uA) I2C interface Transmission speed 400kHz Sensitivity 230-1370 LSB / Gs Resolution 0.73-4.35mGs Frequency of 75Hz Measurement of the magnetic field in three axes of ± 8 Gauss with a resolution of 5 gauss miles Interruption DRDY pin Dimensions of 14 mm x 14 mm Code M0061 Available Price €3.32
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.99
Sensor SCT-013-030, Non-Invasive 30A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features: Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet Code M0203 Available Price €6.49
Charger 2x18650 with EU Plug Cable Charger 2x18650 with EU Plug Cable features: - This product is very convenient and easy to use- Black- Material: metal and plastic- Weight: 74g- Input voltage: AC 100 -240 V 50/60 Hz- Compatible with: 18650 Li-ion- When the 18650 battery is connected to the charger, the red LED light will be displayed, and means green in full charge status- Output: DC 4.2 V, 1A- Plug: EU plug- Cable length: 38cm- The battery are not included Code A0081 Available Price €4.59
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.95
Power Supply Transformer 220V AC/DC 2A 12V Power Supply Transformer 220V AC/DC 2A 12V features:- Input voltage: 100~240V 50Hz- Output voltage: DC 12V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0015 Available Price €4.79
NE555P DIP8 Precision Timer Integrated Circuit NE555P DIP8 Precision Timer Integrated Circuit features: - Blister: DIP8- Number of pins: 8- Step between pins: 2.54 mm- Manufacturer: Texas Instrument - Input voltage VCC: 4.5 - 16 VDC- THRES voltage level: 2.4 - 11.2 VDC- TRIG voltage level: 1.1 - 5.6 VDC- RESET voltage level: 0.3 - 1 VDC- DISCH voltage level change out of state: 0.15 - 0.4 nA- CONT voltage (open circuit): 2.6 - 11 VDC- Low level output voltage: 0.1 - 0.4 V- High level output voltage: 2.75 - 13.3 V - Output current I (O): ± 200 mA- THRES current: 30 - 250 nA- TRIG current: 0.5 - 2 μA- RESET current: -0.4 - 0.4 μA- Current change DISCH out of state: 20 - 100 nA Code T0061 Available Price €0.79
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €15.89 -€3.00 Price €12.89
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.74
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.88
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.74
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.88