USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features: - CH341 driver- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX- High quality, shielded cable- Power and data in the same cable, does not require more adapters- Compatible USB interface 1.1 and 2.0- Support up to 1 mega data transfer- Length 73cm The adapter allows you to connect a computer with: - Electric meters- Decoders, programmers- Cash registers- Satellite TV- Control panels- Mobile phones- Diagnostic interfaces for cars- The administration of Cisco routers Code C0010 Available Price €3.29
Kontakt PCB PLUS Spray 400ml The PCB PLUS cleaner is designed for printed circuit boards.Dissolves waste flux, including resin.The liquid does not attack the substrate or the structural components of the printed circuit boards.The special brush to remove particles and smaller debris. Perfect for cleaning PCB after repair and assembly.PCB Plus Cleanser Spray 400ml features:- Form: spray- Capacity: 400mlApplication:- The product does not leave deposits- It evaporates very fast- Eliminates waste after welding- Perfect in any electronic service- The product does not react with most plastics used in electronics Code Q0071 Available Price €9.95
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.95
Push button 6x6x4mm Push button 6x6x4mm features: -Touch Push Tact Switch mini electronic Arduino push button -Measures: 6x6x4.3mm Code K0079 Available Price €0.21
10x Female-Male Cables 20cm Jumpers Dupont 10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0009 Available Price €1.69
Printed Circuit Board Terminal 2 poles 5.08mm pitch Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 2 poles 5.08mm pitch features: Number of Contacts: 2 Pitch: 5.08mm Number of Rows: 1 Mounting Type: PCB Gender: Male Allowable Section: 1.5mm2 (22- 14 AWG) Termination method: screw Type: screw terminal block Nominal current: 16A Nominal voltage: 250V Color: blue Material: Nylon 66 Depth: 10mm Width: 7.5mm Length: 10mm Code K0217 Available Price €0.25
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.49
Color Recognition Sensor GY-31 TCS230 TCS3200 It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features: - Operating voltage: 3 - 5 VDC- Model GY-91- Chip TCS230 TCS3200 Code M0152 Available Price €9.95
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
Pair of infrared LEDs 3mm Receiver Transmitter Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode. Code S155 Last items in stock Price €0.69
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €6.90
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.15
Color Recognition Sensor GY-31 TCS230 TCS3200 It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features: - Operating voltage: 3 - 5 VDC- Model GY-91- Chip TCS230 TCS3200 Code M0152 Available Price €9.95
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
Pair of infrared LEDs 3mm Receiver Transmitter Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode. Code S155 Last items in stock Price €0.69
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €6.90
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.15