2WD Robot Smart Car Chassis 2x Wheels DIY Ideal for building a car with obstacle detector, light followerIncludes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0003 Available Price €11.50
LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:- Supply voltage of the LED points: 1.8-2.4 VDC- LED color of the dots: red- Pin numbers: 16- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 120mA- Power consumed per segment: 80mW- Segment numbers (points): 64- Diameter of a point: 3mm- Operating temperature: -35 ° C - + 85 ° C- Storage temperature: -35 ° C - + 85 ° C- Screen with common cathode connection for the rows and common anode for the columns- Screen size: 32x32x8 mm Code P0125 Available Regular price €2.89 -€1.00 Price €1.89
Prototype Breadboard Protoboard 840 points for Arduino Prototype Breadboard Protoboard 840 points Arduino features: - 840 Connections - Linkable with other Boards - Base with adhesive to attach it to the work surface - Measures 165x55x8mm Code PB008 Available Price €3.29
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 Available Price €5.99
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.69 -€0.20 Price €2.49
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
W5100 Mini Network Module Ethernet Shield Arduino compatible W5100 Mini Network Module Ethernet Shield Arduino features: - Shield Ethernet for Arduino and compatible boards based on the Wiznet W5100 chip - Provides a simple mode to connect your module to the local network and the internet - Compatible with the official Arduino Ethernet library - With this shield you can build a web server - It can be used as a server or as a client - Controller: Wiznet W5100 - Supports TCP and UDP protocols - Supports up to 4 simultaneous connections - Compatible with all versions of Arduino: UNO, mega 1280/2560 - Dimensions: 50 x 25x 25mm Code W0074 Available Price €10.90
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
Pair of infrared LEDs 3mm Receiver Transmitter Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode. Code S155 Available Price €0.69
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €6.90
Sensor Module ML8511 UV Sensor Module ML8511 UV features: - The module converts the photocurrent into voltage to detect UV intensity - The analog voltage is proportional to UV light detecting - The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use - Power supply: 5V - Analog output - Captured wavelength: 280-390nm - Ultra low power consumption - Meteorological applications, skincare, industrial UV level measurement - Dimensions of PCB: 30x22mm Code S0040 Available Price €5.29
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
Light Sensor Module BH1750 FVI Arduino and Raspberry compatible Descripción: Light sensor module to measure light intensity and obtain digital data from it.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features: - Chip BH1750FVI- Supply voltage 3V-5V- Integrated 16bit AD converter- Detection range: 0-65535 lx (with an accuracy of 1 lux)- Interface: II2C- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)- Dimensions 18.4 x 14 mm Code M0019 Available Price €2.99
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
Light Sensor Module BH1750 FVI Arduino and Raspberry compatible Descripción: Light sensor module to measure light intensity and obtain digital data from it.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features: - Chip BH1750FVI- Supply voltage 3V-5V- Integrated 16bit AD converter- Detection range: 0-65535 lx (with an accuracy of 1 lux)- Interface: II2C- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)- Dimensions 18.4 x 14 mm Code M0019 Available Price €2.99
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €6.90
Pair of infrared LEDs 3mm Receiver Transmitter Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode. Code S155 Available Price €0.69
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.15
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39