Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.39
Charger 2x18650 with EU Plug Cable Charger 2x18650 with EU Plug Cable features: - This product is very convenient and easy to use- Black- Material: metal and plastic- Weight: 74g- Input voltage: AC 100 -240 V 50/60 Hz- Compatible with: 18650 Li-ion- When the 18650 battery is connected to the charger, the red LED light will be displayed, and means green in full charge status- Output: DC 4.2 V, 1A- Plug: EU plug- Cable length: 38cm- The battery are not included Code A0081 Available Price €4.59
Rechargeable battery XTAR 18650 3000mAh Li-ion The battery with PCB protection circuit that protects the battery against overcharges and over-discharges, increasing battery life Rechargeable battery XTAR 18650 3000mAh Li-ion features: - the cell used: Panasonic-Sanyo - capacity: 3000mAh - nominal voltage 3.6V - recommended maximum charge current 1.5A - recommended maximum discharge current 4.5A - maximum charge voltage 4.25V - dimensions: diameter: 18.40mm ± 0.3mm | height: 68.80mm ± 0.5mm - weight 48.5g - quantity: 1 unit Code PP054 Available Price €13.99
30x Rectifier Diodes 1N4148 100V 200mA DO-35 Low Signal High Speed Switching. These diodes are widely used to multiplex signals, such as buttons or digital inputs Characteristic: - Reverse voltage: 100V, - Forward voltage drop: 1V to 10mA, - Forward direct current: 200mA, - Maximum overvoltage current: 4A, - Dissipated power: 500mW, - Recovery time: 4ns, - Configuration: Simple, - Package: DO-35, - Quantity: 30 units . Code T0003 Available Price €0.03
Third hand support for cable soldering Third hand stand for easy soldering of wires with a diameter from 1 to 5mm. Number of holes 5. Code MX0001 ✗ Out-of-Stock Regular price €3.79 -€0.90 Price €2.89
Voltmeter Amperemeter DC Red and Blue 100V 10A Voltmeter Amperemeter DC Red and Blue 100V 10A features: - Supply voltage: 4.5V to 30V - Voltage measurement range: 0V to 100V (± 1%) - Min voltage resolution: 0.1V - Current measurement range: 0A to 10A (± 1%) - Min current resolution: 0.01A - Operating current: 5mA to 15mA - Display: Red LED color (Voltage) and Blue LED color (Intensity) - Includes reverse polarity protection - Measurement refresh time: 500ms - Screen dimensions: 48 x 29 mm - Recessed hole: 45.5 x 26.5 mm - Depth: 21 mm - Cable length: 150 mm - Operating temperature: - 10ºC to 65ºC - No battery needed - Dual panel with voltmeter and digital ammeter Code M0068 Available Price €3.99
Transparent Acrylic Box R3 for Arduino Uno Protection box for Arduino UNO R3 made of high quality acrylic material. Arduino Uno Transparent Acrylic Box R3 features: - Compatible with Arduino UNO - Material: transparent acrylic - External dimensions: 80x 65x 18.5mm Code B0013 Available Price €1.95
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.50
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.45 -€0.50 Price €0.95
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
Ultrasound Distance Sensor HC-SR05 Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:- Power supply: 4.5-5.5 VDC - Supply current: 10 to 40 mA - Activation pin format: 10 μs digital pulse - Echo Pin Output: 0-Vcc - Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below - Measurement range: 2cm to ~ 4.5m - Measurement resolution: 0.3cm - Measurement angle: up to 15 degrees - Measurement speed: 40 Hz, - Connector: standard 5-pin male connector that can be connected directly to boards or breadboards: - 1: VCC - 2: Trig - 3: Echo Code S0047 Available Price €1.95
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.50
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.45 -€0.50 Price €0.95
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
Ultrasound Distance Sensor HC-SR05 Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:- Power supply: 4.5-5.5 VDC - Supply current: 10 to 40 mA - Activation pin format: 10 μs digital pulse - Echo Pin Output: 0-Vcc - Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below - Measurement range: 2cm to ~ 4.5m - Measurement resolution: 0.3cm - Measurement angle: up to 15 degrees - Measurement speed: 40 Hz, - Connector: standard 5-pin male connector that can be connected directly to boards or breadboards: - 1: VCC - 2: Trig - 3: Echo Code S0047 Available Price €1.95
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44