TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €2.15
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
MG-5 Gas Methane Sensor Module for Arduino MG-5 Gas Methane Sensor Module for Arduino features: - Main chip: MQ-5 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm - 10000ppm LPG, LNG, natural gas, propane,- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0029 Available Price €2.53
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0013 Available Price €0.08
2x Insulation Tapes PVC White 10m x 15mm x 0.13mm 2x Insulation Tapes PVC White 10m x 15mm x 0.13mm features:- PVC insulating tape with adhesive- Thickness of 0.13 mm- Measures 10m x 15mm- Quantity: 2 units- Heat resistance: 80°C Code H0032 Available Price €0.99
GPS Module U-BLOX NEO-7M for Arduino - VMA430 This small GPS module is an ideal module for Arduino. The NEO-7 series is characterised by the exceptional performance of the highly sensitive u-blox 7 GNSS (GPS, GLONASS, QZSS and SBAS). Code VE009 Available Price €35.90
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 Available Price €17.95
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
Nova PM Sensor SDS011 - Air quality sensor - High precision laser PM2.5 Dust test module Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air. With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable. Code S0142 Last items in stock Price €32.90
Dehumidifier and air purifier 2 in 1 This air purifier uses a HEPA filter to remove viruses, bacteria, mould, dander, etc. safely. The dehumidifier regulates humidity in the bathroom, kitchen, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE019 Out-of-Stock Price €149.00
Air quality sensor ZP07-MP503 Gas detection The ZP07-MP503 air quality module offers high sensitivity with low power consumption and long life. Calibration before shipment from 10 seconds to 3 minutes max. with automatic warm-up function. Automatic fault check. Code S0150 Available Price €5.45
Air purifier with HEPA filter This air purifier uses a HEPA filter to safely remove viruses, bacteria, mold, mildew, dander, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE018 Last items in stock Price €89.00
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90
CO₂ Humidity and Temperature Sensor - SCD40 (Qwiic) This SparkFun CO2, humidity and temperature sensor incorporates Sensirion's new generation of SCD40 photoacoustic CO2 sensors for highly accurate environmental readings. The sensor is capable of detecting concentrations from 0 to 40000 ppm with high precision above 400-2000 ppm ±(50 ppm+5%). The SCD40 has an integrated CMos® temperature and humidity sensor for greater precision. Code SP097 Last items in stock Price €74.95
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 Available Price €17.95
MH-Z1311A low-power consumption NDIR CO2 sensor Low power CO2 sensor MH-Z1311A, the current consumption is only 150-200uA, waterproof and anti-corrosion, high sensitivity, additionally characterised by excellent linear output. It is very popular used for battery monitors and IAQ devices. Code S0158 Available Price €29.49
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
Nova PM Sensor SDS011 - Air quality sensor - High precision laser PM2.5 Dust test module Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air. With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable. Code S0142 Last items in stock Price €32.90
Dehumidifier and air purifier 2 in 1 This air purifier uses a HEPA filter to remove viruses, bacteria, mould, dander, etc. safely. The dehumidifier regulates humidity in the bathroom, kitchen, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE019 Out-of-Stock Price €149.00
Air quality sensor ZP07-MP503 Gas detection The ZP07-MP503 air quality module offers high sensitivity with low power consumption and long life. Calibration before shipment from 10 seconds to 3 minutes max. with automatic warm-up function. Automatic fault check. Code S0150 Available Price €5.45
Air purifier with HEPA filter This air purifier uses a HEPA filter to safely remove viruses, bacteria, mold, mildew, dander, etc. Filters up to 99.5% of dust, pollen, tobacco smoke, mould spores and pet dander. Keeps the environment clean. Code VE018 Last items in stock Price €89.00
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 ✗ Out-of-Stock Regular price €145.90 -€6.00 Price €139.90
CO₂ Humidity and Temperature Sensor - SCD40 (Qwiic) This SparkFun CO2, humidity and temperature sensor incorporates Sensirion's new generation of SCD40 photoacoustic CO2 sensors for highly accurate environmental readings. The sensor is capable of detecting concentrations from 0 to 40000 ppm with high precision above 400-2000 ppm ±(50 ppm+5%). The SCD40 has an integrated CMos® temperature and humidity sensor for greater precision. Code SP097 Last items in stock Price €74.95
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90