74HC595 SN74HC595N 8-Bit DIP-16

2x LM1117T 3.3V 0.8A Voltage Regulator LDO DC TO-220 features:
- Type Output: fixed
- Voltage Output: 3.3V
- Manufacturer: Texas Ins
- Output Current: 800mA
- Max input voltage: 20V
- Operating temperature: 0ºC to + 125ºC
- Encapsulated: TO-220
- Polarity: Positive
- Quantity: 2 units

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features:
-Micro KW12-3 on / off switch
-Max Current: 5A -AC voltage: 125-250V
-Operating temperature: -40 to 70 degrees C
-Quantity: 2 units

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

Mini Speaker 40mm Diameter 3W Impedance 4 Ohm MP3 features:
- Power 2-3W
- Diameter: 40mm
- Impedance: 4 Ohm
- Quantity: 1 unit

This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately.
The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue).
These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package.
Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors.