Microcontroller ATMEGA8A-PU ATMEGA8 DIP-28 Atmel

A high-performance regulator-booster.
24V battery charger - DC / CV method.
Power supply of the laptop from a 12V car battery.
A high-performance dimmer-regulator.
Charger for Li-Ion, Li-Po batteries etc. - CC / CV method.
LED Constant current driver for LED diodes.
Characteristic:
- Input voltage: 6V -40V
- Output voltage: 1.25-35V (adjustable)
- Output current: 8A, (10A maximum)
- Output power: 300W maximum
- Efficiency of Conversion: up to 95%
- Wiring: Solderless terminal
- Operating frequency: 300kHz
- Ambient temperature exceeds 40 ° C, increase heat dissipation
- LED indicator two-color;
- Charge red
- Fully charged light green
- No charge green

Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:
- Device function: Temperature sensor
- Type of output: Digital
- Supply voltage: 3V to 5.5V
- Accuracy: ± 0.5ºC
- Temperature threshold: Programmable
- Operating temperature: -55ºC to + 125ºC
- Encapsulated: TO-92
- Supply current: 1.5mA

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It incorporates a switch for the connection and disconnection of the entire module.
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth />

It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per Pin I / O 40 mA
- Flash Memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Frequency: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

Batch of 600 Units 1/4W Resistors Various values Ohm Ω features:
- Each lot contains
(30 x 20 units):
10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M
- Tolerance: ± 5%
- Power: 0.25W