2x PCF8574P I/O Extension Board 8574 NXP
  • 2x PCF8574P I/O Extension Board 8574 NXP

2x PCF8574P I/O Extension Board 8574 NXP

T0010

- The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)).
- Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V.
- Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register.

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

2x PCF8574P I/O Extension Board 8574 NXP description

- The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt.
- Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)).
- Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V.
- Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs.

- System Master can read from the input port or write to the output port through a single register.
- The Low current consumption of 2.5μA (typical, static) is ideal for mobile applications and blocked output ports for to drive LEDs directly.
- Internal Power Reset (POR) initializes I / O as inputs with a weak internal pull up current source of up to 100μA.

2x PCF8574P I/O Extension Board 8574 NXP features:

- I2C bus to parallel port expander
- Remote 8-bit I / O pins which by default are inputs at power on
- Full capacity packet sink sink
- Active low open drain interrupt output
- Eight programmable slave addresses using three address pins
- Low standby current is typically 2.5μA < br /> - Operating temperature range -40 ° C to 85 ° C
- Offers ESD protection
- Quantity: 2 units

Customers who bought this product also bought

78L05 Voltage Regulator 5% 5V 100mA TO-92 WS78L05ACZ

Characteristic:
- Output Type: Fixed
- Voltage Output: 5V
- Manufacturer: ST Microelectronics
- Output Current: 100mA
- Input voltage max.: 30V
- Input voltage min.: 7V
- Operating temperature: 0ºC to + 70ºC
- Encapsulated: TO-92
- Polarity: Positive
- Tolerance output voltage: 5%
- Quantity: 1 unit

T0071

Price €0.54

Photoresistor GL5516 LDR

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

S0012

Price €0.15

30x 1N4007 Rectifier Diodes 1A 1000V DO-41

1N4007 Rectifier Diodes 1A 1000V DO-41 features:
- Standard rectifier diode
- Configuration: Simple
- Reverse voltage: 1000V
- Direct voltage drop: 1V
- Direct direct current: 1A
- Maximum overvoltage current: 30A
- Encapsulated: DO-41
- Operational tension: -65ºC to + 125ºC
- Quantity: 30 units

T0002

Price €0.05

NEC IR Remote Control Infrared emitter HX1838

Arduino Raspberry Remote Control HX1838 Infrared Emitter

NEC IR Remote Control Infrared emitter HX1838 features:

- 21 keys
- Measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with UNO module
- Lighting a red 3mm LED by Infrared
Realization of a manageable Infrared robot
- Wiring the IR Distance remote control + Infrared IR Receiver VS1838 with the UNO module
- Fix the IR Distance remote control + VS1838 Infrared IR Receiver in a Mini 2WD DIY Car Robot Kit

W0020

Price €0.98

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

R0036

Price €2.95

4x AA battery holder 4-battery holder with 6V switch

Includes a switch to output the voltage built into the case itself.
It has a cover for protect the batteries.
The cover has perforation in case you want to secure it with a screw (not included).
Characteristic:
- Cable 12cm long
- Measures 70x 65x 18mm
- Battery length max 50mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7)

PP006

Price €1.85
€1.15

0,95 tax excl.

Tax included 1
30+ items
Price €1.15

The minimum purchase order quantity for the product is 2.

Order until 4pm we will send today
30 days return