Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
KFL08 Pillow Block Flange Bearing Spindle housing 8mm with KFL08 CNC bearing features: - Dimensions: Please take a look at the photo - Quantity: 1 unit Code I0099 Available Price €2.39
Color Recognition Sensor GY-31 TCS230 TCS3200 It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features: - Operating voltage: 3 - 5 VDC- Model GY-91- Chip TCS230 TCS3200 Code M0152 Available Price €9.95
DC Gear Motor and Tire Wheel for Smart Car Robot DC Gear Motor and Tire Wheel for Smart Car Robot features:- Voltage: 3 to 6 Vdc- Reduction: 1:48- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0011 Available Price €3.89
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49
1m 6mm GT2 strap 3D printer 1m 6mm GT2 strap 3D printer features: - GT2 rubber strap with fiberglass reinforced - Length: 1m - Width: 6mm - Strap height: 1.38 mm Code I0006 ✗ Out-of-Stock Price €1.95
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.79
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.75
Mini V-groove 2410 wheel with bearings for aluminium profile V2020 Mini V groove wheel with bearings for V2020 aluminum profile. Characteristic: - Outside diameter: 24mm, - Hole diameter: 5mm, - Width: 10mm. Code I0189 Available Price €2.95
Mini double V-groove wheel with bearings for aluminium profile V2020 Idler pulley linear divider pulley with double V groove and bearing. Widely used in many high quality 3D printers and CNC machines Mini double V-groove wheel with bearings for aluminium profile V2020 features: - Outside diameter: 24.5mm, - Inside diameter: 5mm, - Outside diameter deducing grooves width: 21mm, - Wheel width: 11mm, - Distance between the two grooves: 6mm. Code I0163 Available Price €2.95
Mini V-groove 1505 wheel with bearings for aluminium profile V2020 Mini V groove wheel with bearings for V2020 aluminum profile. Characteristic: - Outside diameter: 15mm, - Hole diameter: 5mm, - Width: 9mm. Code I0162 Available Price €2.89
Mini V-groove 2410 wheel with bearings for aluminium profile V2020 Mini V groove wheel with bearings for V2020 aluminum profile. Characteristic: - Outside diameter: 24mm, - Hole diameter: 5mm, - Width: 10mm. Code I0189 Available Price €2.95
Mini double V-groove wheel with bearings for aluminium profile V2020 Idler pulley linear divider pulley with double V groove and bearing. Widely used in many high quality 3D printers and CNC machines Mini double V-groove wheel with bearings for aluminium profile V2020 features: - Outside diameter: 24.5mm, - Inside diameter: 5mm, - Outside diameter deducing grooves width: 21mm, - Wheel width: 11mm, - Distance between the two grooves: 6mm. Code I0163 Available Price €2.95
Mini V-groove 1505 wheel with bearings for aluminium profile V2020 Mini V groove wheel with bearings for V2020 aluminum profile. Characteristic: - Outside diameter: 15mm, - Hole diameter: 5mm, - Width: 9mm. Code I0162 Available Price €2.89