Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa
  • Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa
  • Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa
  • Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa
  • Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa
  • Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa

Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa

I0080

- Measurements:
* Inner diameter D: 4mm
* Outside diameter D: 13mm
* Width - dimension B: 5mm
* Dimension C1: 1mm
* Dimension D1: 15mm
- Quantity: 1 unit

OEM
5905323236684
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Flange Bearing F624ZZ Ball Bearing 3D Printer Reprap Prusa features:

- Measurements:
* Inner diameter D: 4mm
* Outside diameter D: 13mm
* Width - dimension B: 5mm
* Dimension C1: 1mm
* Dimension D1: 15mm
- Quantity: 1 unit

Customers who bought this product also bought

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

RL001

Price €2.39

Heat Shrinkable Tube 5 Colors 3 Meters Package

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

K0047

Price €1.95

PCA9685 digital servo motor controller 16 channel PWM

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

R0074

Price €5.10

UNO Board CH340 clone

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

B0011

Price €7.49

DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

I0012

Price €3.49
€0.85

0,70 tax excl.

Tax included 1
30+ items
Price €0.85

Order until 4pm we will send today
30 days return