Bearing 624zz Ball Bearing 3D Printer Reprap Prusa

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Power Supply Transformer 220V AC/DC 2A 5V features:
- Input voltage: 100~240V 50Hz
- Output voltage: DC 5V
- Output current: 2A
- DC connector: 5.5 mm x 2.1 mm
- Cable length: Approx. 90 cm
- Indicator of operation: LED diode

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations.
Characteristic:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 45 V
- Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32
- Factory soldered temples
- 4-layer PCB, 2 oz. Copper for improved heat dissipation
- Short-circuit and overtemperature protection - Use potentiometer to adjust the current
- Measurements: 20x16x12 mm

Wheel with double V groove and high precision bearing and tolerances Ideal for precise linear movement with V-extrusion.
Double V-groove wheel with high precision and tolerances features:

24mm x 10mm

inner 5mm

Kit wheel including:
- 1 dual V wheel,
- 2 bearings,
- 1 washer 5mm,
- 1 1/4 aluminum spacer,
- 1 25mm M5 bolt,
- 1 nylock nut.

Servos Tester features:
- 3-Channel Tester
- For Electronica Arduino

A3967 controller, double H-bridge controller driver.
Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features:

- Minimum operating voltage: 7.00 V
- Voltage maximum operating: 30 V