Shield Sensor Expansion Board Arduino compatible V2.0 Arduino Shield Sensor Expansion Board V2.0 features: The Mega Sensor Shield V2.0 allows: - To be directly punched to an Arduino Uno, Mega, Leonardo board - Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more - Size: 100x54x12 mm Code M0129 ✗ Out-of-Stock Regular price €3.89 -€0.90 Price €2.99
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €3.19 -€1.00 Price €2.19
IR Remote Control + IR Infrared Receiver VS1838 IR Remote Control + IR Infrared Receiver VS1838 features: - The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal - Vcc supply: 3.3V-5V - IN digital output to connect to the port Arduino I / O - Remote measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module - Light a 3mm red LED by Infrared Code W0021 Available Price €2.49
Resistor 150R Ohm 5% 0,25W 1/4W Resistor 150R Ohm 5% 0,25W 1/4W features:-150R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0006 Available Price €0.08
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino compatible Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features: -Micro KW12-3 on / off switch -Max Current: 5A -AC voltage: 125-250V -Operating temperature: -40 to 70 degrees C -Quantity: 2 units Code K0018 Available Price €0.59
Motor 28BYJ-48 5V Stepper The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48 - Motor phases: 4 - Operating voltage: 5V - Frequency: 100 Hz - Operating current: 200mA - Max Power: 20W - Winding resistance: 70 ohm - Angle per step: 5,625º - Steps per lap: 64 - Torque: 0.3 Kgr / cm - Speed: 1900 rpm - Operating temperature: -45ºC to + 125ºC - Motor cable length: 19cm - Motor block diameter: 28mm - Motor dimensions: 42mm x 32mm x 30mm Code R0044 Available Price €2.29
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Regular price €1.95 -€0.26 Price €1.69
Motor Nema 23 28.5kg JK57HS112-4204 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 28.5 kg/cm. Comes with a 50 cm cable. We have the best stepper motors at the best prices! Perfect for CNC machines! Code I0168 Available Regular price €67.90 -€5.00 Price €62.90
Servo 9g SG92r 2.5kg 9g digital servo new version of SG90. POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque. It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features: Weight: 9g Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v) Gear type: POM with carbon fiber Operating speed: 0.1sec /60degree (4.8v) Temperature range: 0„ƒ_ 55„ƒ Dead band width:1us servo wire length: 25 cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm Code R0079 Available Price €4.30
Gear Reducer Motor 6V DC 200RPM for Smart Car Gear Reducer Motor 6V DC 200RPM for Smart Car features: - Voltage: 3 to 6V DC- Speed without load: 200 RPM to 6V DC Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles - Wiring of the 6V DC 200 RPM motor with the L298N double bridge H controller module Code R0045 Available Price €2.39
Dupont female-female connector cable to PH2.00 for Nema motor Dupont female-female connector cable to PH2.00 for Nema engine features: Dupont 2.54 female to PH2.00 female connecting cable for Nema motor Length 100cm Code I0177 Available Price €1.95
Continous Rotation 360 Degree Servo S3003 Continous Rotation 360 Degree Servo S3003 features: - Operating voltage: 4.8 V to 6 V- Torque max.: 4.1kg / cm (6V)- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)- Radio max.: 360º- Temperature range: -20º + 60ºC degrees- Weight: 38 g- Cable length: 26cm- Dimensions: 40.5 x39x 20 mm- Servo connector: JR- Chinese manufacture Code R0019 Available Regular price €7.95 -€0.96 Price €6.99
M3 Hexagonal Spacer 25mm Male - Female Brass Characteristic: -Metric thread M3 -Male-Female separator 25mm -Quantity: 5 units Code H0048 Available Price €0.45
25T metal disc for MG996R servomotors + 4 screws Metal disc diameter 25mm with 4 mounting holes for 25T RC MG996R servos 25T metal disc for MG996R servomotors + 4 screws features: - Material: Aluminum - Gear teeth: 25T - 4x M3 mounting holes rotated - Diameter disc: 25mm - Includes: 4 fixing screws. Code R0076 Available Price €0.90
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €8.95 -€1.00 Price €7.95
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
Wheel for continuous rotation servo SG90 Servo FS90R Wheels for 360 degree continuous rotation servo motors type SG90, FS90R, SG92r. The wheels have silicone tyres and measure 60 mm (2.36″) in diameter. Four additional mounting holes for 4-40 bolts allow the wheel to be used with several of our universal mounting bracket. Code R0091 ✗ Out-of-Stock Price €1.90
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Available Price €2.95
Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 Available Regular price €11.50 -€1.55 Price €9.95
Mounting Bracket for Nema Engine 17 42mm Mounting Bracket for Nema Engine 17 42mm features: - Steel bracket for PAP Nema 17 3D printer motor - Mounting bracket of 42mm L shape alloy steel for The NEMA17 3D Stepper Motor Printer - Material: Alloy Steel - Size: 5 x 5 x 5cm - Black Color - Fit for 42mm Stepper Motor as NEMA17 Code I0044 Available Price €3.75
Geared Motor with Encoder (6V 1:48 L Shape) Geared Motor with Encoder (6V 148 L Shape) features: - Voltage: 3 to 6V DC- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0070 Available Price €3.29
Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.90 -€0.41 Price €1.49
5x Hexagonal Separator M3 10mm Male-Female Brass 5x Hexagonal Separator M3 10mm Male-Female Brass features: -Metric thread M3-Male-Female Separator 10mm-Quantity: 5 units Code H0047 Available Price €0.39
Red Propeller + Micro Motor 3V 5 6V DC DIY for Arduino Small 3V-6V DC motor ideal for DIY projects Code R0033 Available Price €1.77
Geared Motor with Encoder 6V 1:120 for Arduino Smart Car Robot Geared Motor with Encoder 6V 1120 Arduino Smart Car Robot features:- Voltage: 3 to 6Vdc- Speed without load: 200 RPM to 6Vdc- No-load current: 110mA at 3Vdc - 250mA at 6Vdc- Reductive: 1: 120 Code R0043 Available Price €3.45
Slip ring mini 12mm diameter 12 wires A sliding ring capable of holding up to 12 wires of 12mm diameter. Code R0092 Backorder Price €33.95