Resistor 2,2K Ohm 5% 0,25W 1/4W

Compass is based on a QMC5883L system, which allows you to specify the direction of the earth's magnetic field. Digital Compass Magnetometer GY-271  features:

• 3.3V - 6V power supply voltage
• Current consumption of 100μA (standby 2uA)
• I2C interface
• Transmission speed 400kHz
• Sensitivity 230-1370 LSB / Gs
• Resolution 0.73-4.35mGs
• Frequency of 75Hz
• Measurement of the magnetic field in three axes of ± 8 Gauss with a resolution of 5 gauss miles

• Interruption DRDY pin
• Dimensions of 14 mm x 14 mm

2x Insulation Tapes PVC Blue 10m x 15mm x 0.13mm features:
- PVC insulating tape with adhesive
- Thickness of 0.13 mm
- Measures 10m x 15mm
- Quantity: 2 units
- Heat resistance: 80°C

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Dupont Connector 2.54mm Female features:
- Connector for soldering or crimping
- Lot 100 units
- Ideal for your projects electronic, arduino, but can also be used with other microcontrollers

Positive Voltage Regulator TS117B 3.3V 1Amp Low Dropout features:
- Blister: SOT-223
- Number of pins: 3
- Step between pins: 2.29 mm
- Manufacturer: from China
- VDD power supply voltage: 12V
- Adjustable output voltage V (OUT): 1.8 - 3.3 V
- Line regulation: 0.2% - 0.5%
- Load regulation: 0.05% - 1.0%
- Fall voltage: 1.3 - 1.5 V
- Limiting current I (CL): 1.5 A
- Adjustment of current change: 90 μA
- Minimum load current: 10 mA
- Current in inactive state: 5 - 10 mA
- Wave rejection: 60 - 70 dB
- Thermal regulation: 0.004 - 0.02% / W
- Temperature stability: 0.5%
- Long-term stability: 0.03 - 1.0%
- Average quadratic output noise: 0.003%
- Thermal resistance, connection to the case: 15 ° C /

Plastic box compatible with Raspberry Pi B +, Raspberry Pi 2 and 3. Perfect to protect your Pi. Black Box for Raspberry Pi features:
- Case size: 94x63.5x30mm
- Does not include Raspberry Pi

Female Strip 40 Short Pins features:
- Pin spacing: 2.54mm
- Insert position: Vertical
- Insert: Pasante
- Quantity: 1 unit of strips of 40 female pins each

Easily convert water level to analog signal
The analog output signal can be read directly on the Arduino board
Characteristic:
- Operating voltage: 3.3V -5 V
- Consumption: less than 20 mA - Sensor type: Analog
- Operating temperature: 10º C -30º C
- Detection area: 40 mm x 16 mm
- Dimensions: 60 mm x 20 mm