Resistor 330K Ohm 5% 0,25W 1/4W

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Prototype Protoboard Breadboard 170 points Arduino features:
- 170 connections
- Base with adhesive to attach it to the work surface
- Measurements: 45x35x9mm
- Various colors

Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:
- Based on the MP1584EN regulator
- Output Voltage: 1.6V - 26V DC (adjustable)
- Input Voltage: 4.5V - 28V DC
- Max. Output Current: 3A (with heat sink)
- Frequency: 1MHz
- Conversion Efficiency (1A): 94%
- Short circuit protection
- Protection against overheating
- Operating temperature: -40ºC to + 85ºC
- Measures 22 x 17 x 4 mm

Display OLED 0.96" 128x64 White I2C 4 Pin features:
- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degree
- Screen color: white
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer , instruments, DIY projects, etc ...
- It is an OLED display module with white display and with a dot matrix of a resolution 128x64 and an IC2 interface.
- The display includes the IC driver SSD1306 128 x 64 OLED / PLED Segment / Common Driver.

A bridge rectifier KBPC5010 is an array of electronic components, which is present in most voltage sources; The bridge is formed regularly by 4 diodes, connected in a specific way, and its function is to transform the alternating current to direct current. Bridge Rectifier 50A/1000V KBPC5010 features:
- Metal housing
- Type of diode: bridge rectifier
- Type of bridge: a phase
- Maximum driving voltage: 1000 V
- Maximum driving current: 50 A
- Peak inverse voltage: 1 kV
- Direct voltage Vf (max.) To If: 1.1V @>

Resistor 1K Ohm 5% 0,25W 1/4W features:
-1K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm