5x Strip 16 Pin Female Short

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Switch Button 8x8mm on-off features:
- Switch terminals: Weldable
- Measures: 8x8x13mm

Mini Speaker 40mm Diameter 3W Impedance 4 Ohm MP3 features:
- Power 2-3W
- Diameter: 40mm
- Impedance: 4 Ohm
- Quantity: 1 unit

Descent module.
Use a multimeter to check the output voltage and adjust the potentiometer.
Control of voltage and current.
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Current output: adjustable, 4.5A (max 5A)
- Output power: 75W maximum
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 180KHz
- Efficiency conversion: up to 96%
- Short circuit protection: Yes (limited current 8A)
- Protection over temperature: the output switches off automatically
- Size: 62mm x 26mm x 14mm
Principal functions:
- Step-down converter with overcurrent protection
- Li-Po battery charger, Li-Ion

Includes a switch to output the voltage built into the case itself.
It has a cover to protect the batteries.
The cover has perforation in case you want to secure it with a screw (not included).
Battery holder 2x AA Battery holder with switch features:

- Cable 15cm long
- Measurements 68x 32x 18mm
- Battery length max 50mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7)

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features:
- 3-pin connector: 1- GND
2- VCC
3- Voltage is recovered depending on the magnetic effect
- Supply voltage: 5VDC
- Output current: 40mA

M18 Inductive Proximity Sensor features:
- Inductive proximity sensor detection switch LJ18A3-8-Z / BX
- NPN DC6-36V
- A Often used for 3D printer bed leveling
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open )
- Detecting distance 8mm
- DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition)
- Head diameter 18 mm
- Size 6.9 x 2cm
- Cable length 90cm