Power Adapter 220VAC DC 5.1V, 3A USB-C

Dupont Connector 2.54mm Female features:
- Connector for soldering or crimping
- Lot 100 units
- Ideal for your projects electronic, arduino, but can also be used with other microcontrollers

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers

HD V2 Raspberry Pi camera board The Raspberry Pi High Definition (HD) camera board connects to any Raspberry Pi or Compute Module to create HD photos and video.
Uses Sony's IMX219PQ image sensor that offers high-speed, high-speed video images Sensitivity.
Raspberry Pi Camera Module offers reduced image contamination such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection.
Raspberry Pi Camera Board, Sony IMX219 8 Megapixel Sensor features:
High-quality images
High data capacity
Fixed 8 megapixel focus (includes focus adjustment tool)
Compatible with 1080p, 720p60 and VGA90
Sony IMX219PQ CMOS image sensor
15-pin ribbon cable

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.
Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features:
- Type: 3-axis accelerometer
- Chip: ADXL345
- Supply voltage: 3-5V
- Consumption: 40uA active and 0.1uA on hold
- Communication: SPI and I2C
- Measurements: Static and dynamic acceleration
- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g
- Resolution: 13 bits
- Dimensions: 20x16mm
- Operating temperature: -40 °C to +80 °C
- Detection: Free fall, click-double click

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

TP4056 5V Micro USB Lithium Battery Charger Module features:
- Based on TP4056ES regulator
- Lipo micro USB Li-Ion charger
- Input Voltage: 4.5V - 5.5 VDC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Indicator LED: charging red, charging green
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A
- Measurements: 25x19x5 mm
- Ideal for 18650 batteries

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level