Push Switch Button B3F Omron Yellow Key

10x Linear Potentiometers 10k OHM kΩ features:
- Horizontal variable resistance PCB
- 10k Ohm kΩ Linear
- Quantity: 10 units

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

Arduino Sensor Shield V5 APC220 features:
Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate
- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more

LED Diode Assortment Kit 15 pcs 5mm red, green, yellow features:
- Lens color: red, green, yellow - diffuse
- Size: 5mm
- Operating current: 20mA
- Voltage (red) 1,8V-2,3V
- Voltage (green) 3,2V-3,4V
- Voltage (yellow) 1,8V-2,3V
- Anode (A): Positive (long leg): 28mm
- Catode (K): Negative (short leg): 25mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: +260ºC
- Quantity: 30 units
*5x red
*5x green
*5x yellow

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

LED Diode Assortment Kit 50x Red Green Yellow Blue White features:
  
- Lens color: Red, green, yellow, blue - diffuse, light white
- Size: 5 mm
- Operating current: 20mA
- Voltage (red) 1.8V-2.3V
- Voltage (green) 3.2V-3.4V
- Voltage (yellow) 1.8V-2.3V
- Voltage (blue) 3.0V-3.2V
- Voltage (white) 3.2V - 3.4V
- Anode (A): Positive (long leg): 17mm
- Cathode (K): Negative (shorter leg): 15 mm
- Operating temperature: -25ºC / 80ºC
- Welding temperature: + 260ºC
- Quantity: - 50 units
                  - 10x red
                  - 10x green
                  - 10x yellow
                  - 10x blue
                  - 10x white

Addressable 5050 RGB LED bar (5mm x 5mm) with low current draw. LEDs can be joined by connecting the output of one module to the input of another.
Data line with a very specific protocol, requires a real-time microcontroller AVR, Arduino, PIC, mbed, etc. A minimum 8 MHz processor is required.

check it Contenido:
- 20x Cable macho-macho 20cm - 10x Cable hembra-macho 20cm - Kit de diodos LED - 20 unidades ( 5x rojo, 5x verde, 5x amarillo, 5x blanco) Resistencias:
- 220R- 10 unidades
- 10k- 5 unidades
- 1k-   5 unidades
- Transistor TIP120 TO-220 - 1 unidad
- Diodo LED RGB - 1 unidad
- Condensador electrolítico 470uF/50V - 2 unidades check it Content:
- Prototype plate 400 points
- 20x Cable Jumper mach-macho
- LED diode kit - 30 units (10x red, 10x green, 10x yellow) Resistances:
- 100k- 10 units
- 10k- 10 units
- 1k- 10 units
- 220R- 10 units
- Photoresistor GL5516 Type LDR 10k - 2 units
- Push buttons Omron B3F Blue, Red, White - 3 units
- 100uF / 50V electrolytic capacitor - 5 units