DIP Switch - DS-04 Horizontal High Profile 4 Positions

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 100.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

Laminated Copper Clad Prototype PCB Circuit Board 10x15cm, 0.35um double side.

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

Heat Shrinkable Tube 5 Colors 3 Meters Package features:
- Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas.
- These heat shrink tubes are very flexible and of high quality. Made in EU
- Different sizes of 20 cm each are delivered:
* 1,6mm: black, brown, red, yellow, orange
* 2,4mm: black, brown , red, yellow, blue
* 3,2mm: black, brown, red, yellow, blue
- Quantity: 15 units
- Material: polyolefin
- Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter)
- Minimum shrinkage temperature: 115 ° C maximum 200 ° C

74HC00N DIP14 Input Positive Logic NAND Gates features:
- Blister: DIP14
- Number of pins: 14
- Step between pins: 2.54 mm
- Manufacturer: Texas Instrument - Input voltage VCC: 2 - 6 VDC
- High level input voltage V (IH): 1.5 - 4.2 VDC
- Low level input voltage V (IL): 0.5 - 1.8 VDC
- Input voltage V (I): 0 - 6 VDC
- Output voltage V (O): 0 - 6 VDC
- High level output voltage V (OH): 1.9 - 5.9 VDC
- Low level output voltage V (OL): 0.1 - 0.33 VDC - Leakage current I (I): ± 1000 nA
- I (DC) supply current: 20 mA - Operating temperature: -40 ° C to 85 ° C
- Storage temperature: -65 ° C to 150 ° C

Resistors 470R Ohm 5% 0,25W 1/4W features:
- 470R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Perfect kit to learn programming in the middle of Arduino the basic of electronics It allows to build various projects of various complexity, from the easiest ... to the most complicated.
The elements are placed in the box to keep everything in order.   Characteristic:   It includes the following module references:   - 1x UNO R3 Rev3 ATmega328 ATmega16U2 Development Board Arduino Module - 1x LED Display Screen Controller Blue Backlight 16x2 1602 HD44780
- 1x Prototype Protoboard MB-102 830 points Arduino
- 1x ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Proto V5.0
- 1x 74HC595 74595 SN74HC595N 8-Bit Shift Register DIP-16
- 1x LM35 Temperature Sensor LM35DZ TO92
- 2x SW-520D Vibration Tilt Sensor

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B