Push button 6x6x4mm
  • Push button 6x6x4mm

Push button 6x6x4mm

K0079

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

OEM
5905323237896
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Push button 6x6x4mm features:

-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

Customers who bought this product also bought

Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

W0108

Price €7.43

2x PCF8574P I/O Extension Board 8574 NXP

- The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)).
- Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V.
- Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register.

T0010

Price €0.95

Passive Buzzer PCB Long Blue

This module is a passive buzzer, a low trigger level alarm for Arduino. It emits different sounds at various frequencies. The buzzer sounds when the I / O port input is low level. 

M0163

Price €1.07

BD139 Plastic Medium-Power Silicon NPN Transistors pack 5ps

BD139 Plastic Medium-Power Silicon NPN Transistors pack 5ps features:
Material: Silicon Polarity: N-P-N Encapsulated: TO 126 Audio amplifier, driver
VCBO collector-base voltage: 60V VCEO collector-emitter voltage: 60V VEBO emitter-base voltage: 5V Collector continuous current: 1.5A Typical gain of direct current. hfe: 40-160
Maximum power dissipation: 12.5 Watt if T <= 25ºC Working frequency: 250 MHz

Typical gain of direct current. hfe: 40-160

T0075

Price €0.82

10x Electrolytic Capacitor 470uF 10V 105ºC

10x Electrolytic Capacitor 470uF 10V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 470uF
-Maximum tension: 10V
-Maximum temperature 105º C
-Dimensions: 8x12mm
-Quantity: 10 units

D0095

Price €0.11

DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

M0099

Regular price €5.36 -€2.00 Price €3.36

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

RL001

Price €1.98
€0.17

0,17 tax excl.

1
30+ items
Price €0.17

Order until 4pm we will send today
30 days return