Momentary Switch Push Button Red N/O 7mm

Desoledring Pump with Heater 40W 220V features:
- It allows to remove tin
- Easy to use with one hand.
- Desoldering pump with heater
- Consumption: 40W
- CE Certificate
- Quantity: 1 unit

Resistor 10K Ohm 5% 0,25W 1/4W features:
-10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

5x Electrolytic Capacitor 1000uF 35V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 1000uF
-Maximum tension: 35V
-Maximum temperature 105º C
-Dimensions: 13x21mm
-Quantity: 5 units

Definition of the Hall effect: When a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicularly to the direction of current flow, a voltage, called the Hall voltage, proportional to the magnetic field, and the current appears on the side faces of the bar.
This voltage is proportional to the speed of movement of the charge carriers, It is considerably higher in semiconductor materials than in metal conductors. Magnetic Sensor Characteristic: - Input Voltage: 3.8-30VDC - Output current: 40mA
High output current capacity -40 mA maximum absolute
Quad-Hall design virtually eliminates static mechanical effects
Magnetic compensated temperature - Digital current sinking output

0.96" 128x64 Blue-Yellow I2C 4-Pin OLED display features:
- Interface: I2C (logical level 3.3V)
- Resolution: 128x64
- Angle of view:> 160 degrees
- Screen color: blue and yellow (1/4 above yellow and 3/4 below blue)
- Screen Dimension: 2.43cm / 0.96 "
- IC Controller: SSD1306
- Power supply: 3.3V - 5VDC
- Operating temperature: -20 ° C - 70 ° C
- Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 "
- Application: smart watch, MP3, thermometer, instruments, DIY projects, etc ...
- It is an OLED screen module with blue-yellow display and with a resolution dot matrix 128x64 and an IC2 interface.
- The display includes the driver controller SSD1306 128 x 64 Segment Driver / OLED / PLED Common.

Resistor 2,2K Ohm 5% 0,25W 1/4W features:
-2.2K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features:
- Operating range: 0.2mm to 15mm
- Receiver: Phototransistor
- Emitter: Infrared Led
- Wavelength: 950 nm

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328