Prototype Board 25 Points pack 6unds

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Resistor 330 Ohm 5% 0,25W 1/4W features:
-330 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features:
- Operating voltage: 3 - 5.5 VDC
- Measurement operating temperature: -55 ° C - 125 ° C
- Output current: 5 μA
- Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C
- Storage temperature: -55 ° C - + 125 ° C
- 100% new and high quality
- Module DS18B20 temperature measurement sensor
- The DS18B20 sensor has a pull-up resistor
- Power indicator LED on the module

It is compatible with almost any microcontroller, Arduino, PIC, AVR.
It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features:
- Supports Quick CRYPTO1 and MIFARE
- Operating current: 13-26mA at 3.3V
- Standby current: 10-13mA to 3.3V
- Sleep-mode current: <80μA
- Maximum current: 30mA
- Frequency of operation: 13.56Mhz
- Reading distance: 0 to 60mm
- Communication protocol: SPI
- Maximum SPI speed: 10Mbit / s
- Maximum data rate: 10Mbit / s
- Operating temperature: -20 to 80ºC
- Humidity of operation: 5% -95%

DC Gear Motor and Tire Wheel for Smart Car Robot features:
- Voltage: 3 to 6 Vdc
- Reduction: 1:48
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

- HC-05 Bluetooth transceiver module with base
- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.
- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.
Bluetooth Transceiver Module HC-05 Wireless features:
- Chipset CSR BC417
- 3.6 to 6 Vdc power supply
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Reach approx. 10m
- Security: Authentication and encryption.
- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.