Inlet Module Plug Fuse Switch 220V C14 3D Printer

Version compatible with Arduino Mega2560 R3
It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader
With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports)
The board includes a USB connector, an ICSP port , a reset button and some status LEDs
Arduino compatible Mega2560 R3 CH340 board features:

- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Digital I / O Pins: 54 (14 PWM outputs)
- Analog input pins 16
- DC current per I / O Pin 40 mA
- DC Current per Pin 3.3V 50 mA
- Flash: 256 KB of which 8 KB are used by the bootloader
- SRAM: 8 KB
- EEPROM: 4 KB - Clock speed 16 MHz

Mini Submersible Water Pump DC 5.5-12V 200L / H 3W
Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features:

* Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm

Speed controller for DC motor (PWM) 6V-28VDC 3A PWM 6V 12V 24V features:
- Ideal to control the speed of DC motors
- Input voltage: 6-28VDC
- Max continuous output current: 3A
- Max power: 100W
- Dimensions: 50x17x28mm
- PWM frequency: 21kHz
- Adjustable duty cycle: 5% -100%
- Keep in mind that the voltage applied to the motor will be the supply voltage applied to the circuit

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

Nozzle Head 0.4 1.75mm MK8 3D Printer Extruder features:
- MK8 Precision Nozzle: 0.4mm
- Material: Copper
- Size: 13mm x 6mm
- Suitable for Filament: 1.75mm
- Quantity: 1 unit

Rocker switch 6A 250VAC / 10A 125VAC ON / OFF 4 pins DPST Double NO contact

2x Female 40-Pin Long Strip features:
- Pin spacing: 2.54mm
- Pin length: 10.5mm
- Insert position: vertical - Insertion: through
- Quantity: 2 units of female strips of 40 pins each

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32