Potentiometer B100K linear

10x Electrolytic Capacitor 100 uF 50V 105ºC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 100uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 6x11mm
-Quantity: 10 units

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

2x Insulation Tapes PVC Blue 10m x 15mm x 0.13mm features:
- PVC insulating tape with adhesive
- Thickness of 0.13 mm
- Measures 10m x 15mm
- Quantity: 2 units
- Heat resistance: 80°C

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Resistor 4,7M Ohm 5% 0,25W 1/4W features:
-4.7M Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features:
- Booster module
- The output voltage may be greater than the input voltage
- Use a multimeter to check the output voltage and adjust the potentiometer
- Input voltage: 2-24V
- Output voltage: 5-28V
- Current output: 2A - Operating temperature: -40ºC to + 85ºC
- Conversion efficiency: up to 93%
- Size: 17.5 x 30 mm

COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)
- The light intensity is greater without concentrating the beam of light
- Greater durability
- Angle of opening up to 160ºC
- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.

5x Push Switch Button B3F Omron Blue Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm