9-pin male sub-D connector for soldering in copper alloy 9 way mounting solder sub-D male connector. 9-pin male sub-D connector for soldering in copper alloy features: - Nominal voltage: 500 VAC - Nominal current: 5 A - Number of ways: 9 - The connectors are supplied with stamped and formed contacts - Straight male connector - Tin-plated and notched housings offering good grounding and continuity - Tin-plated solder barrel terminations - Good EMI / RFI protection - Insulating material: fiberglass polyester Code K0196 Available Price €0.69
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.79
Bearing 605ZZ 5mm Ball Bearing 3D Printer Reprap Prusa - Measurements: Inside diameter d: 5mm Outside diameter D: 14mm Width - dimension B: 5mm - Quantity: 1 unit Code I0079 Available Price €0.69
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.39
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.99 -€0.50 Price €3.49
KP08 Pillow Block Mounted Bearing 8mm 8mm Bore Pillow Block Mounted Bearing is often suited to support rotating shaft applications. Code I0144 ✗ Out-of-Stock Regular price €3.49 -€1.20 Price €2.29
Adapter module CH340G LC Technology -TTL UART 5V series This is a CH340G TTL UART 5V serial adapter, designed to allow adding a USB connection to your project. In addition, this opens up the possibility of programming microcontrollers like the Arduino Pro mini. This module allows you to connect your project, from programming small microcontrollers to a custom computer keyboard. The module is ready for use of a UART connection. This may require the installation of a driver; however, it is a standard driver distributed by Microsoft Windows Update, available in Linux and that can be configured in MAC OS. Adapter module CH340G LC Technology -TTL UART 5V series features: - Manufacturer: LC Technology, - Communication chipset: CH340G - Communication: UART, - Pin connection: Code M0186 Available Regular price €2.50 -€0.51 Price €1.99
Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs - Ideal for fix on the axis of the motors of your 3D printer Code I0004 Backorder Regular price €1.94 -€0.50 Price €1.44
Pulley GT2 60 Teeth 5mm Aluminium 3D Printer Reprap CNC Pulley GT2 60 Teeth 5mm Aluminium 3D Printer Reprap CNC features: - Number of teeth: 60 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 44mm - Inner hole: 5mm - Use with strap: 6-7mm GT2 Ideal to fix on the axis of the motors of your 3D printer, CNC machine. Code I0104 Available Price €3.59
GT2 Strap Kit 2m + Pulley GT2 16 Teeth pack 2pcs GT2 Strap Kit 2m + 2x Pulley GT2 16 Teeth 6mm features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - GT2 strap made of rubber with fiberglass reinforced - Length 2m - Width: 6mm - Belt height: 1.38 mm Ideal to fix on the axis of the motors of your 3D printer. Code I0005 Backorder Regular price €7.69 -€1.37 Price €6.32
Pulley GT2 40 Teeth 6mm Aluminium 3D Printer Reprap CNC Pulley GT2 40 Teeth 6mm Aluminium 3D Printer Reprap CNC features: - Number of teeth: 40 - Pitch: 2mm - Material: Alloy aluminum - Outside diameter: 27mm - Inside hole: 5mm - Use with strap: 6mm and 6.35mm Code I0103 Available Price €2.85
Smooth Pulley GT2 Aluminium 5mm 6mm Smooth Pulley GT2 Aluminium 20T features: - Material: Aluminum alloy - Outside diameter: 17.80mm - Inside hole: 5mm - Use with belt: 6mm Size is equal to 20T pulley only without tooth Code I0156 Available Price €2.84
Pulley GT2 36 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 36 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 36 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 25mm - Inner hole: 5mm - Use with strap: 6mm and 6.35mm - Ideal to fix on the axis of the motors of your 3D printer Code I0032 Available Price €2.95
Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap features: - Number of teeth: 20 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 16mm - Inner hole: 8mm - Use with strap: 6mm and 6.35mm - Toothed width 7mm - Quantity: 1 unit - Ideal for fixing on the axis of the motors of your 3D printer Code I0063 Available Price €1.95
Smooth pulley GT2 Aluminium Inner diameter 3mm Smooth pulley GT2 6mm Aluminium Inner diameter 3mm features: - Material: Aluminum alloy - Outside diameter: 12.80mm - Inside hole: 3mm - Use with strap: 6mm For toothless strap. Code I0161 Available Price €2.49
Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs - Ideal for fix on the axis of the motors of your 3D printer Code I0004 Backorder Regular price €1.94 -€0.50 Price €1.44
GT2 Strap Kit 2m + Pulley GT2 16 Teeth pack 2pcs GT2 Strap Kit 2m + 2x Pulley GT2 16 Teeth 6mm features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - GT2 strap made of rubber with fiberglass reinforced - Length 2m - Width: 6mm - Belt height: 1.38 mm Ideal to fix on the axis of the motors of your 3D printer. Code I0005 Backorder Regular price €7.69 -€1.37 Price €6.32
Smooth pulley GT2 Aluminium Inner diameter 3mm Smooth pulley GT2 6mm Aluminium Inner diameter 3mm features: - Material: Aluminum alloy - Outside diameter: 12.80mm - Inside hole: 3mm - Use with strap: 6mm For toothless strap. Code I0161 Available Price €2.49
Smooth Pulley GT2 Aluminium 5mm 6mm Smooth Pulley GT2 Aluminium 20T features: - Material: Aluminum alloy - Outside diameter: 17.80mm - Inside hole: 5mm - Use with belt: 6mm Size is equal to 20T pulley only without tooth Code I0156 Available Price €2.84
Pulley GT2 40 Teeth 6mm Aluminium 3D Printer Reprap CNC Pulley GT2 40 Teeth 6mm Aluminium 3D Printer Reprap CNC features: - Number of teeth: 40 - Pitch: 2mm - Material: Alloy aluminum - Outside diameter: 27mm - Inside hole: 5mm - Use with strap: 6mm and 6.35mm Code I0103 Available Price €2.85
Pulley GT2 36 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 36 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 36 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 25mm - Inner hole: 5mm - Use with strap: 6mm and 6.35mm - Ideal to fix on the axis of the motors of your 3D printer Code I0032 Available Price €2.95
Pulley GT2 60 Teeth 5mm Aluminium 3D Printer Reprap CNC Pulley GT2 60 Teeth 5mm Aluminium 3D Printer Reprap CNC features: - Number of teeth: 60 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 44mm - Inner hole: 5mm - Use with strap: 6-7mm GT2 Ideal to fix on the axis of the motors of your 3D printer, CNC machine. Code I0104 Available Price €3.59
Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap features: - Number of teeth: 20 - Pitch: 2mm - Material: Aluminum alloy - Outside diameter: 16mm - Inner hole: 8mm - Use with strap: 6mm and 6.35mm - Toothed width 7mm - Quantity: 1 unit - Ideal for fixing on the axis of the motors of your 3D printer Code I0063 Available Price €1.95