Terminal for JST PHR Female Connector 2mm

Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 2 poles 5.08mm pitch features:
Number of Contacts: 2
Pitch: 5.08mm
Number of Rows: 1
Mounting Type: PCB
Gender: Male
Allowable Section: 1.5mm2 (22- 14 AWG)
Termination method: screw
Type: screw terminal block
Nominal current: 16A
Nominal voltage: 250V
Color: blue
Material: Nylon 66
Depth: 10mm
Width: 7.5mm
Length: 10mm

M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features:
- This sensor can be configured as auto Z axis level
- Sensor detection switch inductive proximity LJ12A3-4-Z / BY
- PNP DC6-36V
- Often used for 3D printer bed leveling
- Typical application: printer bed level sensor 3D
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- PNP NO (Normal Open)
- Detecting Distance 4mm - DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum
- Operating temperature -25 ° C at + 55 ° C (Non-freezing condition)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

Polarity cannot be reversed by mistake.
90 degree angle connector. JST PHR-2 Connector Male Angle 3 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: female connector Connector class: male Connector type: conduit-plate Contactor raster: 2mm Number of pins: 3 Electrical mounting: THT Working voltage: 100V Working current: 2A Working temperature: -25 ... 85 ° C Spatial orientation: horizontal data sheet PH series

Polarity cannot be reversed by mistake.
90 degree angle connector. JST PHR-2 Connector Male Angle 2 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: female connector Connector class: male Connector type: conduit-plate Contactor raster: 2mm Number of pins: 2 Electrical mounting: THT Working voltage: 100V Working current: 2A Working temperature: -25 ... 85 ° C Spatial orientation: horizontal data sheet PH series

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

Includes a switch to output the voltage built into the case itself.
It has a cover to protect the batteries.
The cover has perforation in case you want to secure it with a screw (not included).
Battery holder 2x AA Battery holder with switch features:

- Cable 15cm long
- Measurements 68x 32x 18mm
- Battery length max 50mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7)