4WD Robot Smart Car Chassis 4x Wheels DIY

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Characteristic: - Supply voltage: 4.5V- 5.5V
- Consumption: 30 mA typical
- Analog output
- Range: 10cm to 80cm
- Dimensions: 29x12mm
- Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino

Continous Rotation 360 Degree Servo S3003 features:
- Operating voltage: 4.8 V to 6 V
- Torque max.: 4.1kg / cm (6V)
- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)
- Radio max.: 360º
- Temperature range: -20º + 60ºC degrees
- Weight: 38 g
- Cable length: 26cm
- Dimensions: 40.5 x39x 20 mm
- Servo connector: JR
- Chinese manufacture

A3967 controller, double H-bridge controller driver.
Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features:

- Minimum operating voltage: 7.00 V
- Voltage maximum operating: 30 V

This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases.
On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND
2- VCC
3- analog output - the voltage depending on the light
- Supply voltage: 3.3 V-5VDC
- PCB size: 19x15x8 mm

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

Geared Motor with Encoder (6V 148 L Shape) features:
- Voltage: 3 to 6V DC
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Reduction: 1:48