UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €5.70
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.30
Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0090 Available Price €0.40
Raspberry Pi 4 Modelo B 4GB RAM The Raspberry Pi 4 Model B is the latest product in the Raspberry Pi family of computers. This product is in the 4GB RAM version, with 2GB (B0068) and 1GB (B0067) versions also on offer. Code B0069 ✗ Out-of-Stock Price €49.50
Sensor Module FZ0888 IR Infrared Speed Meter Sensor Module FZ0888 IR Infrared Speed Meter features: - The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position - The module has a digital output (DO) which can be connected to your preferred microcontroller. The operating mode: - When the sensor is blocked, the DO output is high - The AO signal is not enabled in this module - Power supply: 3.3-5V - Power consumption current 20 mA max - PCB dimensions: 32 x 14 mm Code S0038 Available Price €1.56
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €13.13 -€3.00 Price €10.13
10x Female-Male Cables 20cm Jumpers Dupont 10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0009 Available Price €1.40
2WD Round Robot Chassis Turtle Car 2x Wheels 3x Plates DIY for Arduino Contents: - 3x Round transparent chassis plate diameter of 14cm - 2x DC 5V gearbox motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 to 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0007 Backorder Price €14.54
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €13.13 -€3.00 Price €10.13
Mclon Kit ProtoShield DIY The mClon kit is ideal for building a car with obstacle detection and light tracking. In addition to the platform, the kit contains the basic essentials for building your first robot including the Arduino Uno compatible board, distance sensors and many other components. Check the complete list in the product description Code R0085 Available Regular price €46.48 -€14.25 Price €32.23
2WD Robot Smart Car Chassis 2x Wheels DIY Ideal for building a car with obstacle detector, light followerIncludes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0003 ✗ Out-of-Stock Price €9.50
Mclon Car Chassis 2x DIY Wheels Ideal to build a car with an obstacle detector, light follower Characteristic: - Voltage: 3 to 6Vdc - No load speed: 100 RPM to 6Vdc - No load current: 90mA to 3Vdc - 180mA to 6Vdc - Wheel dimensions: diameter 65mm - width 26mm The kit includes: - aluminum platform - 2x wheels and 2x motors - 1x idler wheel - screws Code R0078 Available Price €19.79
2WD Round Robot Chassis Turtle Car 2x Wheels 3x Plates DIY for Arduino Contents: - 3x Round transparent chassis plate diameter of 14cm - 2x DC 5V gearbox motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 to 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0007 Backorder Price €14.54
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €13.13 -€3.00 Price €10.13
Mclon Kit ProtoShield DIY The mClon kit is ideal for building a car with obstacle detection and light tracking. In addition to the platform, the kit contains the basic essentials for building your first robot including the Arduino Uno compatible board, distance sensors and many other components. Check the complete list in the product description Code R0085 Available Regular price €46.48 -€14.25 Price €32.23
2WD Robot Smart Car Chassis 2x Wheels DIY Ideal for building a car with obstacle detector, light followerIncludes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0003 ✗ Out-of-Stock Price €9.50
Mclon Car Chassis 2x DIY Wheels Ideal to build a car with an obstacle detector, light follower Characteristic: - Voltage: 3 to 6Vdc - No load speed: 100 RPM to 6Vdc - No load current: 90mA to 3Vdc - 180mA to 6Vdc - Wheel dimensions: diameter 65mm - width 26mm The kit includes: - aluminum platform - 2x wheels and 2x motors - 1x idler wheel - screws Code R0078 Available Price €19.79