Keyboard Shield 16x2 LCD screen for Arduino It is made up of a 16-character, 2-row, 6-button display. The display is compatible with the HD44780 controller and is connected in 4-bit mode so it can be used directly through the Arduino LiquidCrystal library. Ideal to navigate through the different parts of the configuration or map. Keyboard Shield 16x2 LCD screen for Arduino features: > - 2x16 LCD with blue backlight and white characters - Potentiometer to modify the LCD contrast - 5-push-button keyboard + RESET - Use of the minimum possible channels - Full compatibility with Arduino UNO and Mega - The display is compatible with the HD44780 controller - Response time: 30 ms - Size: 80 x 60 x 22 mm Code P0020 Available Price €4.49
Power Supply Transformer 220V AC/DC 2A 9V Power Supply Transformer 220V AC/DC 2A 9V features:- Input voltage: 100 ~ 240V 50Hz- Output voltage: DC 9V- Output current: 2A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0098 Available Price €3.99
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.49
DC Gear Motor 6V 1:48 for Arduino DC Gear Motor 6V 148 Arduino features:- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0008 Available Regular price €1.90 -€0.41 Price €1.49
5x Push Switch Button B3F Omron Red Key 12mm 5x Push Switch Button B3F Omron Red Key 12mm features:- 5x Push Buttons B3F Omron Key- Maximum current: 50 mA- Tension DC: 24V- Operating force: 1.27N- Switch terminals: weldable- Contact: SPST-NO- Contact resistance: 100M Ohm- Type of action: Superficial- Measures: 12x12x7.3mm Code K0073 Available Price €0.20
LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:- Supply voltage of the LED points: 1.8-2.4 VDC- LED color of the dots: red- Pin numbers: 16- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 120mA- Power consumed per segment: 80mW- Segment numbers (points): 64- Diameter of a point: 3mm- Operating temperature: -35 ° C - + 85 ° C- Storage temperature: -35 ° C - + 85 ° C- Screen with common cathode connection for the rows and common anode for the columns- Screen size: 32x32x8 mm Code P0125 Available Regular price €2.89 -€1.00 Price €1.89
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Last items in stock Price €6.95
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
Extension Board Shield Nano V3.0 ATmega328P Extension Board Shield for Arduino Nano V3.0. Code B0025 Available Price €2.95
TPA3116D2 2X50W Amplificador Doble Canal Audio amplifier for dual-channel loudspeakers. Supply voltage: 12-24 V. Maximum power: 2x50W. Power consumption: 3-5A. Code M0206 Last items in stock Regular price €13.59 -€2.00 Price €11.59
2x AAA 3V battery holder for Micro:bit Weight: 12.7g Box size: 62 * 25 * 10 mm Code PP037 Available Price €1.99
SONOFF 5050RGB - LED strip light IP65 2M 2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included) Code WS061 Available Regular price €10.95 -€2.00 Price €8.95
SONOFF L1 - Intelligent LED strip light WiFi IP65 5M Intelligent 5 metre LED strip by WiFi and RF, great for creating any atmosphere in any room. Change its colour and rhythm from your mobile phone or its remote control. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. Code WS016 ✗ Out-of-Stock Price €36.99
Lilypad Power Supply 5V Step Up with AAA Batteries This module is a small source of energy, this board was designed to be as small and as indiscreet as possible.Putting a battery type AAA and operating the power switch, will have a supply of 5 V to power a lilypad circuit.Use up to 200ma, it is protected against short circuits. This card has AAA battery clips but can use a 1.2V to 5V input, the module increases the voltage up to 5V.Lithium polymer batteries are an alternative to rechargeable batteries.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Power Supply 5V Step Up with AAA Batteries features: - Type of batteries connectable: AAA- Input voltage (of the batteries): from 1.5V to 5V- Output voltage: 5V Code M0140 Available Regular price €7.99 -€2.50 Price €5.49
Blue silicone protective cover for BBC Micro:Bit Protective cover used for micro: bit. The cover has two different sides, dot matrix display area, finger usage area on the front. Micro USB interface, power interface and reset button on the back side. It can be installed on a micro: bit board to make your work more charming and fun. Weight: 10g Size: 5.5 cm * 6.5 cm Material: gel silica (environmental protection material) Code RA045 ✗ Out-of-Stock Price €5.00
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €3.19 -€1.00 Price €2.19
Cables with Crocodile Clips pack 10pcs Include 5 different colors, 1 unit of each color.Also available in batches of 5 and 2 cables. 10x Cables 50cm with Crocodile Clips features: -Length: 50cm-Colors: red, green, white, black and yellow-Cable diameter: 1,5mm -Quantity: 10 cables Code K0013 Available Price €2.95
BBC micro:bit V2.2 - WiFi Single Board Micro-Computer, BLE 5.0, Microphone + Speaker + Accelerometer The novelty of micro:Bit v2.2 for a more lively introduction to technology for children. The micro:bit is a pocket computer that can be encoded, customized and controlled for the implementation of digital ideas and games. It measures just 4x5cm and features a fun and easy to use design, so users can create anything from games and animations to slick stories at school, at home or anywhere - all it takes is imagination and creativity. It is fully programmable. This means that each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer, Bluetooth 5.0 technology, microphone and speaker. It contains a quick start guide in the same package. Code B0120 Available Regular price €20.95 -€1.00 Price €19.95
BBC micro:bit V2.2 Go - Starter Pack The novelty of micro:Bit for a more lively introduction to technology for children. The micro:bit is a pocket computer that can be encoded, customized and controlled for the implementation of digital ideas and games. It measures just 4x5cm and features a fun and easy to use design, so users can create anything from games and animations to slick stories at school, at home or anywhere - all it takes is imagination and creativity. It is fully programmable. This means that each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer, Bluetooth 5.0 technology, microphone and speaker. It contains a quick start guide in the same package. Code B0125 Available Regular price €23.95 -€0.96 Price €22.99
Power Supply Transformer 220V AC/DC 1A 9V Power Supply Transformer 220V AC/DC 1A 9V features:- Input voltage: 100 ~ 240V 50Hz- Output voltage: DC 9V- Output current: 1A- DC connector: 5.5 mm x 2.1 mm- Cable length: Approx. 90 cm- Indicator of operation: LED diode Code A0067 Available Price €3.99
Gravity: Analog TDS Sensor/ Meter for Arduino Arduino compatible analog TDS (Total Dissolved Solids) sensor to measure water hardness, water purity. It can be used to test water quality in domestic, hydroponic and other applications. Measures TDS from 0 ppm to 1000 ppm. Power supply from 3.3V to 5.5V. Code DF028 Available Price €15.99
LattePanda V1 - A powerful 2GB/32GB mini-PC This is a LattePanda (DFR0444) with 2GB RAM and 32GB EMMC memory. The minicomputer is equipped with a 1.92 GHz Intel Cherry Trail Z8350 Quad Core processor. In addition, it has WiFi, Bluetooth 4.0, 2x USB 2.0, 1x USB 3.0, microSD slot, Ethernet port and an additional ATmega32u4 microcontroller with 20 GPIO pins known from Arduino. This version comes with Windows 10 installed, but does not include a Windows 10 activation key. Code DF023 Available Regular price €152.40 -€12.00 Price €140.40
USB charging / data cable - USB Type C 3A 1m white This cable will instantly charge the battery of your smartphone or tablet: it is compatible with devices equipped with a USB Type-C port. When connected to a computer, the cable works in two ways: it transmits data and also charges batteries. Code KH043 Available Price €2.49
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
Raspberry Pi Pico The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA124 Available Price €4.99
Lilypad Arduino compatible USB ATmega32u4 Board The LilyPad Arduino USB is a microcontroller board based on the ATmega32u4.It has 9 digital input / output pins (of which 4 can be used as PWM outputs and 4 as analog inputs), an 8 MHz resonator, a micro USB connection, a JST connector for a 3.7V LiPo battery and a power button. restartIt contains everything necessary to support the microcontroller; simply connect it to a computer with a USB cable or a battery to start.The LilyPad Arduino USB differs from previous LilyPad cards in that the ATmega32U4 has built-in USB communication, eliminating the need for a separate USB to serial adapter. This allows the LilyPad Arduino USB to appear on a connected computer as a mouse and keyboard, as well as a virtual serial / COM (CDC) port. Code M0147 Available Regular price €7.99 -€1.00 Price €6.99
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90
NVIDIA Jetson Nano Module, Small AI SOM, 4GB/16GB EMMC NVIDIA Jetson Nano Module (B01), Production-Ready AI System On Module (SOM), 4GB 64-bit LPDDR4 with 16GB EMMC Flash. Code RA152 Last items in stock Price €165.90
MyoWare LED Shield This LED shield goes in set with the MyoWare Muscle Sensor. It is a 10-segment bar graph showing the reads from the sensor. Put the two together and you get a great system that allows you to measure and show your muscle activity. Pretty cool, huh? The shield comes equipped with a LiPo power source making it full autonomous. Code SP025 Last items in stock Price €44.99