LIPO battery 590mAh 3.7V
  • LIPO battery 590mAh 3.7V

LIPO battery 590mAh 3.7V

PP056

Lithium polymer battery 3.7 V with the capacity of 590 mAh. Includes PCM safety chip (protection against overcharge, over-discharge, short circuit).

Battery terminal type-3 wires.

Battery voltage-3.7 V

Battery capacity- 590 mAh.

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Lithium polymer battery 3.7 V with the capacity of 590 mAh. Includes PCM safety chip (protection against overcharge, over-discharge, short circuit).

Features:

Battery type- Lithium polymer.

Battery terminal type-3 wires.

Battery voltage-3.7 V

Battery capacity- 590 mAh.

Embedded PCM safety chip (protection against overcharge, over-discharge, short circuit).

Dimensions:

Battery length/depth- 52 mm.

Battery width/diameter- 33 mm

Three wires with 3-pin connector 4 mm apart.

Wires: Red: positive, Black: negative.

Yellow: thermistor output.

Customers who bought this product also bought

Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

W0108

Price €8.99

TP4056 Module Lithium Battery Charger with Protection Micro USB

TP4056 Module Lithium Battery Charger with Protection features:
- TP4056 Li-Ion Micro USB Charger
- Upgraded version of previous TP4056
- Micro USB connection to charge directly from the PC
- Ideal for 18650 batteries
- Based on the TC4056A regulator
- Input Voltage: 4.5V - 5.5V DC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Overvoltage protection 4.2V
- Over discharge protection 2.4V
- LED indicator: charging blue, charging red
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Overcurrent protection: 3A
- Measurements 26 x 19 x 5 mm
- Possibility of current change through Rprog

A0026

Price €1.69

Attiny85 Digispark USB Development Board

Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter.
Similar to the Arduino line , It is one of the smallest boards on the market.
Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others.
You can use many of the same Arduino libraries and have your own on the digispark wiki. Attiny85 Digispark USB Development Board features:
-USB power supply
-External power supply (7v-35v DC 12v maximum recommended)
-5V DC 500mA regulator on board
-Programmable with the Arduino IDE
-Loaded with Micronucleus bootloader

B0001

Price €4.95

ESP-12F ESP8266 12F WiFi Board Module

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

W0064

Price €3.09

MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB

MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features:
- Booster module
- The output voltage may be greater than the input voltage
- Use a multimeter to check the output voltage and adjust the potentiometer
- Input voltage: 2-24V
- Output voltage: 5-28V
- Current output: 2A - Operating temperature: -40ºC to + 85ºC
- Conversion efficiency: up to 93%
- Size: 17.5 x 30 mm

A0065

Price €1.69

LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power

Descent module.
Use a multimeter to check the output voltage and adjust the potentiometer.
Control of tension.
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:
- Input voltage: 4.5-38V
- Output voltage: 1.25-36.5V
- Current output: 2A (max 3A with heat sink)
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 150KHz
- Efficiency conversion: up to 92%
- Load Regulation: +/- 0.5%
- Voltage Regulation: +/- 2.5%
- Protection over temperature: the output switches off automatically
- Size: 62mm x 38mm x 15mm
Principal functions:
- Step-down converter with overcurrent protection
- Voltmeter up to 40V, remember to set the input voltage to 4.5V

A0013

Price €3.99
€5.95

4,92 tax excl.

Tax included
Out of stock
Do you want to receive an alert when product is back in stock?
 
We will send you an email once the product becomes available. Your email address will not be shared with anyone else.
Price €5.95

Order until 4pm we will send today
30 days return