Resistor 330 Ohm 5% 0,25W 1/4W Resistor 330 Ohm 5% 0,25W 1/4W features:-330 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0009 Available Price €0.07
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.47
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Regular price €8.22 -15% Price €6.99
Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 Manufacturer: Taiwan Semiconductor 5x Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 features: - Type Output: fixed- Voltage Output: 3.3 V- Output Current: 800mA- Max input voltage: 12V- Operating temperature: -20C to + 85ºC- Encapsulated: SOT223- Dropout Voltage Vdo: 1.3V (1A)- Quantity: 5 units Code T0001 ✗ Out-of-Stock Price €0.62
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.15
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
Ultrasound Distance Sensor HC-SR05 Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:- Power supply: 4.5-5.5 VDC - Supply current: 10 to 40 mA - Activation pin format: 10 μs digital pulse - Echo Pin Output: 0-Vcc - Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below - Measurement range: 2cm to ~ 4.5m - Measurement resolution: 0.3cm - Measurement angle: up to 15 degrees - Measurement speed: 40 Hz, - Connector: standard 5-pin male connector that can be connected directly to boards or breadboards: - 1: VCC - 2: Trig - 3: Echo Code S0047 ✗ Out-of-Stock Price €1.61
IR Remote Control + IR Infrared Receiver VS1838 IR Remote Control + IR Infrared Receiver VS1838 features: - The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal - Vcc supply: 3.3V-5V - IN digital output to connect to the port Arduino I / O - Remote measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module - Light a 3mm red LED by Infrared Code W0021 Last items in stock Price €2.06
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 ✗ Out-of-Stock Price €13.97
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €7.40 -€3.00 Price €4.40
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €14.79 -€1.41 Price €13.38
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 ✗ Out-of-Stock Regular price €9.88 -€2.40 Price €7.48
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €7.40
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €5.78
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Last items in stock Price €8.26
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Regular price €7.93 -€1.00 Price €6.93
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2 inch 320x240. Shied 40pins. Code P0165 ✗ Out-of-Stock Price €13.97
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 4 control signals.. It has a resolution of 128x160 pixels. Easily programmable with UNO module, Arduino, Raspberry, Mega2560. Code P0208 Available Regular price €7.40 -€3.00 Price €4.40
LCD TFT Touch Screen Display 3.2 inch 320x240 LCD TFT Touch Screen Display 3.2inch 320x240, shield 34 pins. Code P0107 Available Regular price €14.79 -€1.41 Price €13.38
2.4 inch TFT LCD screen 240x320 SPI LCD TFT Display Module 240x320 2.4 SPI features: - LCD screen TFT 240x320 pixels- 262,000 possible colors (18 bit)- Pixel: RGB vertical band- Driver ILI9341- SPI interface- 8-bit digital interface, 4-bit control lines- Resistive touch screen 4 - cables- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Helpful Links: Wiring of the TFT LCD screen 2.4 SPI - Connect the TFT 2.4 SPI LCD screen with the UNO module Display graphics and texts on the LCD TFT screen 2.4 SPI Program a touch calculator on the LCD screen TFT 2.4 SPI Code P0001 ✗ Out-of-Stock Regular price €9.88 -€2.40 Price €7.48
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €7.40
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €5.78
LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD LCD TFT Display Screen 2.4 240x320 UNO Mega2560 SD features:- LCD screen TFT 240x320 pixels- Power 2.8-3.3V- 262,000 possible colors (18 bit)- 8/16 bit parallel bus digital interface- LCD Controller: ILI9325- Touch screen controller: XPT2046- Touchscreen, resistive touch screen- Manual use or with any type of pointer- SD card reader- Connector: 2 x 20 pins 2.54mm- Dimensions PCB 75x55 mm- Dimensions LCD 59x42 mm- Ideal for projects with ARDUINO Uno Mega, AVR, STM Code P0005 Last items in stock Price €8.26
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €6.53
Pantalla LCD TFT 2.4 pulgadas 240x320 SPI - Pantalla LCD TFT 240x320 pixels- 262.000 posibles colores (18 bit)- Pixel: RGB vertical stripe- Controlador ILI9341 - Interface SPI - 8 bit interfaz digital, 4 bit líneas de control- Pantalla táctil resistiva 4 - wires- Ideal para proyectos con ARDUINO, Uno R3, MEGA2560 Enlaces útiles : Cableado de la pantalla LCD TFT 2.4 SPI - Conectar la pantalla LCD TFT 2.4 SPI con el módulo UNO Visualizar gráficos y textos en la pantalla LCD TFT 2.4 SPI Programar una calculadora táctil en la pantalla LCD TFT 2.4 SPI Code P0110 Available Regular price €7.93 -€1.00 Price €6.93